Equipment always has its own service life. This also applies to LCD monitors. Often they break due to failure of the backlight. But there is a way out of this situation, so do not throw out such a technique. To resume its work, alteration of the monitor backlight to an LED is enough.
Details
When looking for the right parts, you may come across the fact that there will be no fluorescent lamps on sale. And replacing the backlight of the monitor with an LED alone will not be difficult. Often use LED strip.
Breakdown rating
Before you start mounting the tape in the display, you need to evaluate the degree of breakdown. To identify this, you need to know some subtleties. The failure of light bulbs in the backlight may be due to the following reasons.
Firstly, an initial production defect is possible.
Secondly, the lamps could be damaged when the device falls or from hitting it with something.
Thirdly, sometimes short circuits occur in the metal part of the lamp.
Fourth, the lamps could simply fail, having worked out the time they set. Simply put, they could burn out.
When spinning up the display, it is easy to determine the presence of malfunctions and establish the causes that led to the breakdown.
To qualitatively replace the display lighting, you need to understand the principles by which a liquid crystal matrix is integrated in all types of modern devices with screens.
LCD Matrix Principles
In every modern monitor, LCD matrices work in accordance with the principle of clearance. That is, the device works with lighting, the bulbs of which shine through the entire matrix.
But keep in mind that the quality of the display is directly dependent on the type of lighting.
In televisions and stationary monitors at this point in time, direct-lighting is often used. That is, the LED lamp is located on the entire surface of the panel.
To illuminate the matrix, 2 blocks are used. Each unit includes two lamps. They are located at the top and bottom of the display. As a result, placing them in this way creates uniform illumination of the entire matrix.
This arrangement leads to the fact that the lighting works even when any lamp breaks. Inverters are responsible for the power of these bulbs.
As soon as any of the bulbs breaks and stops working, the inverter notes that the lighting has become uneven. Therefore, he stops working. This function is built into it to avoid further problems in the backlight. So often the inverter provokes a situation when, after the breakdown of one of the 4 bulbs, the backlight lasts for some time.
After mastering this information, you can proceed directly to the process of installing a new backlight.
Process
To correctly install the LED backlight for the monitor, you will need to follow a number of rules. It is important to do everything in a clearly established order. So, the first thing you need to establish is whether the backlight actually broke, since it is not alone that is responsible for supplying light. This can be easily understood by disassembling the display.
Often a breakdown of this nature is found in TV monitors, computers. The screen may turn on and then turn off again after a short time. Before remaking the monitor on the LED backlight, it is necessary to disassemble it first. This is not at all difficult to do. The process is the same for a variety of display models, and when installing the LED backlight in the LD 22 monitor and other similar displays, you can use the same instructions.
Disassembly
It is not particularly difficult to describe this procedure in detail, however, each type of equipment has a number of features, monitors and sizes differ, and manufacturers assemble them differently. But in the procedure the same steps are always present, there is only variability at some points. Therefore, common points can simply be described.
First of all, they remove the stand by unscrewing the screws holding it, together with the other fasteners of the case.
Any device has a special groove designed to open the latches by prying the lid with flat objects. It is located at the end. When disassembling the monitor for the first time, it should be borne in mind that the latches will be pressed tightly, but subsequently it will be easier and easier to deal with them.
After that, the metal frame is removed. For this purpose, the latches are pushed back or the screws are removed from the housing. For people who have already replaced the monitor’s backlight with an LED strip or replaced parts on such devices, the procedure will seem very simple. After this process, the wires are disconnected from the circuit board.
Then go to the matrix, access to which is currently open. It has a lot of connecting cables, which are very fragile. Therefore, you should exercise extreme caution when working with it. The best solution would be to lay the matrix aside and cover it with a cloth so as not to accidentally hurt, damage and prevent dust from accumulating on it. If the work was done correctly, access to the inverter, electronic circuit board and lamp will open. Working with them is now easy. If a person decided to tackle the conversion of lamp backlight to LED in the monitor, he needs to keep in mind how all the removable parts were located in it. They are difficult to confuse, but beginners should consider the possible risks of confusing their location.
The next step in altering the backlight of the monitor to LED is to disconnect each lamp from the matrix. After removing the grooves from it, you can pull out the sources of the current backlight and get rid of them. Those who have not yet installed the LED backlight on the monitor screen need to remember that mercury is contained in CCFL lamps. For this reason, you should be vigilant and always exercise caution when working with them.
At the next stage, the alteration of the lamp backlight to LED in the monitor directly replaces the light source.
Own backlight
It is important to remember that the LED strip is chosen for this procedure. It is best for these purposes to take a set of LED backlight for a monitor with the already taken size of the lamps or choose the one whose length will be slightly larger. So, in 1 meter it should be at least 120 light bulbs. In order for the conversion of the monitor backlight to LED to be effective, you need to choose colors that will not put pressure on your eyes. Otherwise, there is a risk that a person will redo everything in the second round.
Best of all, by installing the LED backlight of the monitor with your own hands, give preference to white bulbs. Tapes with crystals 3528 and 4115 are perfectly suitable. Their sizes should be suitable for the seats where the tapes will be installed. Most often, the size is 7 mm. The LED strip in the backlight monitor may contain a different number of lamps, its advantage is that in any case it will last longer than its predecessors. After that, the tape is fixed using double-sided tape. Place the LED strip instead of the monitor backlight in the same place where the previous lamps were.
Usually these are small grooves. Sometimes old wires from removed light sources are used to further connect them to power sources. Prior to this, it is necessary to check whether the LED backlight has been correctly collected. For this purpose, it is connected using wires to external power sources - batteries.
In the next stage, the LED backlight of the monitor screen is connected to power. Power board is always available on the displays of both computers and televisions. In order for the replacement of the monitor backlight with LED to be effective, this moment should be paid more attention. Those who have experience connecting low-voltage devices to a network with a voltage that exceeded the indicative standards, remember that in this case the equipment burns out. This will happen because the resistance of the device is not designed for such a value. You will need to find the 12 V conclusions on the board and solder the wires from the new lamps with them. When connecting the LED backlight of the monitor, it is important to remember that polarity is observed.
Having done this, you can proceed to the assembly of the TV or computer.
disadvantages
The LED strip installed instead of the monitor backlight lamps has one significant minus. Since everything is connected directly, it is not possible to regulate and disconnect it. Therefore, it is always on when the display turns on. The LED backlight of the monitor matrix, connected with your own hands, will be too bright, eyes will get tired of it. However, this problem is solved.
Create adjustment
After replacing the monitor backlight with LED, proceed to adjust the backlight. To do this, work with wires that were connected to the tapes to add them the ability to turn on and off when certain buttons are pressed. There are two ways to create them.
In accordance with the first, a circuit is assembled, by means of which the power and intensity of the lamps are adjusted. To this end, do the following.
- Take the plastic connector, which is located on the display power board. It is not difficult to find it: it is from it that wires are drawn, each socket for which is signed.
- To enable on and off, use DIM sockets. Adjust the brightness by changing the PWM controllers.
- After that, take the field-effect transistor with channel N. Then the negative wires from the LED strip are soldered to the Drain terminal of the field pole. Connect the common wire from the LEDs to the input element Source. The circuit provides for the use of a resistor with a nominal value of 100 to 2000 ohms. It is through it that a Gate transistor is connected to any DIM socket.
- Then solder the wires with a "plus" from the LED backlight. For this purpose, they are output to a 12 V power supply chip, then soldered.
- After performing all of the above steps, the backlight is installed in the fastening places, and then the display assembly is started in the reverse order. Be sure to remember the gentle actions with the matrix, filters. After this item, the display can be used.
The second method is the following procedure for using tapes with LED backlight inverters in monitors mounted in them. Do it this way.
- To connect the circuit of this method, again you need to find the plastic connector with a DIM socket and an on / of output. This is most easily determined using pinouts.
- Using a multimeter, the sockets are called up from the control unit responsible for the display backlight. From them comes the required DIM signal, as well as on / of.
- At the next stage, the wires from the LED inverters are soldered to the detected sockets. To adjust the backlight using inverters, remove the wires that fed the previous lamps.
- Fix them where there is free space, using double-sided tape.
- To complete the alteration of the monitor backlight on the LED finally, check the new lighting in the case.
Using this method leads to good performance of new lamps. Converting the LCD monitor to LED backlighting will please anyone with the fact that the equipment will work much longer.
Reasons for replacement
At the moment, liquid crystal displays, in which the backlight is mounted , have become very popular. This technology has replaced the outdated models, which were of worse quality. However, even with high quality, such devices are sometimes equipped with backlight with obsolete lamps. They never differed in long service life, often failed. It is precisely because of this that lighting often breaks down in modern technology. This is not a very serious trouble, and not in all cases you need to contact a specialist. Reducing the monitor backlight to LED helps to save money.
Why LEDs?
Although at the moment there are a great many manufacturers of displays, all the equipment has approximately the same principle of operation. Therefore, it is very convenient to produce and replace the monitor lamps with LED backlight. It doesn't matter which manufacturer the device is. If even when following the instructions the desired part was not found at the indicated place, then it is in any case hidden nearby. Having looked closely, it will be easy to find.
LEDs are a modern and advanced light source. Most often they use LED strip. When it is necessary to repair the monitor, the LED backlight is selected for the following reasons.
Firstly, she serves for a long time. If you connect it correctly, then it is able to work without quality deterioration for the whole 10 years. No other bulbs used for the same purpose can boast of such a characteristic. They fail much earlier than this period.
Secondly, it is very convenient that the tapes are made on a self-adhesive basis. Therefore, mounting is carried out without any difficulty on any surface, including the rear wall of the display.
Thirdly, LED bulbs have a bright luminous flux. They illuminate the screen quite intensely. If you take into account a number of recommendations, then after altering the LCD monitor to the LED backlight, your eyes will almost never get tired with prolonged contact with the display.
Fourth, you can choose any lighting to your taste.
It is necessary to pay attention to one moment. Although the choice of tapes by type of lighting is always very large - a wide range of them is presented on the shelves, it is best to prefer calm, pastel shades. For example, a yellow or white ribbon would be the best choice. Having chosen such colors, a person in the future will say to himself thanks for this. It will be easier for the eyes to perceive information from the screen precisely with such bulbs.
About tapes
Tapes with LEDs are sold in coils of 5 m. This length is always enough to create an effective and high-quality display backlight.
The product is very simple to connect to the device board. It is enough to follow simple instructions.
Also, tapes are characterized by low energy consumption, despite the fact that the power of the light source is quite large. Most often, LEDs require a voltage of only 12-24 V.
Diodes never get too hot during operation. This is extremely important, since overheating of the bulbs is the cause of the breakdown of the lamps of the structures built into the display.
Old-style bulbs may break due to the fact that the device is often turned on or off. But diodes are not afraid.
LED strips are very resistant to all kinds of external influences. It also contributes to their longevity. Using them, you can be sure that the risks of damage to them are minimized.
Thus, replacing an outdated or defective display illumination leads to many positive consequences. However, before you make the monitor backlight on the LED strip, you should carefully read the instructions, and when performing the task, it is worth carefully following all the recommendations. Then the new backlight will last a long time and will delight the owner.
Myths about LEDs
If you ask each user of equipment with monitors a question, would he replace the LCD with the same, but with LED backlight, in 90% of cases the answer would be yes. However, most will not be able to explain why this will be better than traditional CCFL technologies. In the best case, it will be retold by one of the myths widespread today, with which LED illumination has grown.
However, there is no particular difficulty in understanding LED technology. A little knowledge is enough, and myths about it will be debunked.
Myth number 1: LED monitor is better than LCD.
LED displays are a separate type of technology that is not related to conventional computer monitors. So, they are informational, advertising monitors, which are mounted on the streets in cities. On these monitors, visualization occurs with the use of LED lamps - both one and many, for this reason they are called so. They are bright enough, but their resolution is low.
But LCD monitors of computers with LED backlighting are considered a completely separate phenomenon. Pixels are formed in them still with the assistance of the matrix. In its cells, liquid crystals are controlled by the signal voltage; they help to rotate the plane of polarization of light at the desired angles. So the degree of its penetration is regulated.
When LEDs are installed in the display, the light source changes. The matrix is still responsible for passing it. Usually CCFL lamps are initially installed in displays. They are set on fire by inverters. However, LEDs shine with exactly the same intensity, but consume less power. For this reason, they came to computer monitors.
Therefore, LED displays cannot compete with LCDs, since these are initially different types of devices.
Myth number 2: LED backlighting is the same everywhere as CCFL.
CCFL- . . , , .
, . , . .
. , . -, – . .
-, . , . RGB-, . , . , . , .
. , . , , , , .
: .
- . . . -, . , . , , . LED- .
. . . .
3: LED- .
RGB. , . .
. CCFL. .
4: LED- .
, , , , , . .
. . . LED- CCFL.
5: LED- , CCFL.
- , . , .
. .
, , . .
, , .
, , .
6: LED- CCFL.
It really is. , . , CCFL. .
7: LED- CCFL.
, IT-. , . .
. , , . , , , . , .
CCF- . . . .
9: LED- CCFL.
. RGB LED . .
. CCFL. . , , . .
10: LED- .
, : CCFL, LED, .
. , , . LED- – local dimming.
, , . local dimming , . .
local dimming , , . .
, CCFL.
Therefore, in practice, the myth is confirmed. But if we are talking about a computer monitor, then this indicator is not important to him. More important is the static contrast.
Conclusion
With proper installation of LEDs in the monitor, you can achieve savings, improve the performance of your existing device. Replacement is a fairly simple process. The main thing is to follow the instructions carefully.