You can drag the chair with any material, depending on the taste preferences of the client, the interior design or financial capabilities. Such can be leather, its substitute or other textile analogue.
Components for hauling
Do-it-yourself office chair hauling most often occurs with the following types of materials:
- Genuine Leather. It is considered the most elite and prestigious option. Work with him carefully. Work will require additional tools that will also increase the cost of repairs.
- Faux leather. The best option for the price category, but also the most short-lived. This constriction of an office chair, although cheap, will last such material for no more than 2 years, which is less than that of inexpensive fabric upholstery. There are high quality leather substitutes that are in no way inferior to genuine leather, but their cost is almost equal.
- Textiles. This material has the widest assortment both in colors and in the texture of the fabric. A cheap option is chenille - a fabric consisting of cotton and synthetic fibers. Further in increasing price: flock, jacquard, microfiber and tapestry.
Repair Features
The design of the chair and its material are determined by what it is intended for. It can be a chair of the chief or a management staff or the ordinary employee or the client. The upholstery speaks about the status of a chair. This is often a leather option. Others have cheaper analogues or a textile surface - they are lighter in design and mobile.
When the owner is already very fond of the owner, it is not necessary to buy a new one and get used to it. You can order upholstery of old furniture or do it yourself if skills, materials and tools allow.
Work stages
Do-it-yourself padding for an office chair upholstery is not as difficult as it might seem at first. It is not necessary to call a wizard if you have the right tools and materials at hand. To work, you will need the following elements: fabric for sheathing, foam rubber, scissors or a knife, screwdrivers - cross and flat, furniture stapler.
Before starting work, the chair will have to be disassembled. It is easier to do this if there is an instruction. But often this is missing, so you need to deal with the device and properly disconnect the cover and seat. It is better to photograph the chair before the start of the analysis and in the next stages, because it will be easier to assemble it after repair.
A simple product has standard fasteners, so hauling an office chair with your own hands will not take much time. It is enough to unscrew the bolts and screws in certain places. When the parts of the chair are disassembled, you can proceed with the removal of the old upholstery. To do this, use pliers, a screwdriver and an anti-stapler, if there are staples. After that, by the standards of the old skin, we make patterns on the new material. To do this, simply attach the products to each other and draw a outline.
Next, lay the material on the floor in the following order: casing component, foam rubber and frame (back or seat). Then it’s good to fasten the first one to the frame, while it’s good to pull it in - not to make folds, but gently fix the result with a stapler. Padding an office chair with leather is not only giving an updated look to the furniture, but also raising the status of the organization, especially in the eyes of customers. When both parts are sheathed, you can put the chair back and enjoy the work done.
How to drag a chair with Alcantara?
Material such as Alcantara is widely used in various fields. This is an artificial suede that has a sticky layer underneath. Thanks to this, it perfectly fits to the surface. Alcantara has a good service life (up to 7 years), it is not very extensible, but elastic enough to create convenience for work. The best Alcantara is made in Korea, it should have a 5 x 5 cm grid on the back.
You can drag a chair made in China using the following devices: pliers, a marker, a centimeter tape, scissors, a ruler, a knife, directly Alcantara with self-adhesive.
To prevent overspending of the material, it is necessary to make a calculation. To do this, measure all parts of the chair. Then add 5 cm to each side for allowances. The excess will then be cut off with a clerical knife. After that, you can disassemble the chair by simply unscrewing the necessary elements. Next, cut off the necessary pieces of Alcantara, while noting the dimensions with a marker on the inside.
Should I remove old upholstery?
Padding an office Alcantara chair implies the ability not to remove the old upholstery. Alcantara is such a convenient material that it lies on any surface. The protective base should be separated from the piece and applied to the workpiece, while Alcantara must be leveled so that there are no wrinkles. Wrap excess over edges. They are later fixed or trimmed. At the same time, you need to cut it off immediately, otherwise it will not be possible to detach the Alcantara after an hour.
Hauling the whole chair or part?
Often, users are unhappy with only a particular part of the chair, while it is possible to replace the lining of only the back or seat. The scope of work should be set before they begin.
The hauling of an office chair does not have to be accompanied by an appeal to specialists. You can take advantage of repair tips, arm yourself with the necessary tools and materials and make an independent restoration.
Office chair repair
Often organizations give chairs for repair. Padding office chairs is a simple task, but when the amount of work is large, only professionals can handle it quickly and efficiently. They can arrive at the office or home, measure for free and calculate the exact cost of the work. Also pick up the products for repair and bring back at the appointed time. Often, all the work takes no more than 2-3 days.
Not only upholstery replacement is included in the work of such companies. They can repair the frame of the chair itself, replace the rollers and legs, foam rubber and plywood. The cost and service will depend on the volume and urgency of the work performed. The calculation is based on what parts were used, how much time was spent.
Price
Hauling office furniture is a job for a number of professionals. Now the market is replete with firms that provide similar services. Often they offer the following service:
- Departure of the measurers at the place and drawing up an estimate of work;
- transportation of a chair;
- product dismantling;
- preparation of upholstery material according to sketches;
- Direct hauling office chair;
- return of the finished product at the expense of the company.
Each organization has its own price list for the services provided, and prices can vary from 500 rubles and above. Not only the material matters, but also the design of the chair, its dimensions and initial cost.
The constriction of the office chair, the price of which depends not only on the cost of the company’s services, but also on what kind of upholstery material will be chosen by the customer, will help to restore the old look of the old furniture. As a rule, the catalog is provided by the company itself, it presents both genuine leather and its substitutes, as well as textile analogues.