The D-Link DAP 1360 device, which is configured effortlessly, is available in two different versions on the market. This device is able to function both as a normal router and as a router. It will be a great solution for those who wish to purchase a wonderful device for creating a wireless access point for their home.
The device settings are generally understandable, there is a slight difference in the options of the two types of this router. In the article, we will consider what each revision is, what functions they are equipped with and how the firmware is implemented.
general information
The DAP 1360 router is an open source access point. As a rule, it is used for work in small offices and homes.
The device is universal. It has 7 different options that allow you to create and expand a wireless network. When choosing the necessary implementation, you need to understand in what mode the router will work. It is capable of being a repeater, wireless client, access point, WDS bridge, and AP. The device in addition to the above can work with two WISP modes. It has antennas, which are the signal receivers from the provider.
The router runs on Linux. The kit comes with a disk with special software that allows you to quickly figure out the functionality of the DAP 1360. Setting up the router using software will be almost instant and easy. Internal memory - 16 MB.
Feature Overview
The equipment works with three standards - b / g / n. Thanks to this, the speed of the Internet will be high and high quality, as far as the provider allows. Modern encryption protocols are used, which filter by MAC addresses.
The highest data transfer rate is 150 Mbps. Due to the presence of antennas, the coverage area is quite extensive. According to consumers, the speed is more than enough for ordinary home use.
Access point, repeater, bridge - such functions are inherent in the B1 revision of the DAP 1360 router. Its configuration is quite simple, all the nuances are described below. Another revision may be a router, so it is quite realistic to call it a full-fledged router. The difference between the latest modification and modern devices from another manufacturer is that it has only one LAN port. Although the standard amount is 4.
Revision B1 setup
Configuring DAP 1360 revision B1 is a little different than another modification. This is because it does not work as a router. This unit is most often used as a conventional device for distributing a wireless signal and interacting with it.
In order for the equipment to work properly, you need to make some settings in the computer itself. First, connect the device to a PC via a network cable. Then in the “Control Panel” find the “Network” menu. An access point is selected there. The owner of the router is interested in the "Properties" section. In the "Protocols" you need to change the address, subnet mask and gateway. All data is standard and can be found in the device manual.
Network Settings
If you want modification B1 to work in the mode of a wireless access point, then the following manipulations should be performed.
In the browser, go to the router settings menu. To do this, you need to write the address of the device in the search line (it is standard and is indicated in the instructions). After a successful system boot, a window will open asking you to enter your login and password. The first line should be written admin, and the second - leave empty. In the "Settings" menu, open the LAN section. A window appears asking you to select a connection. It is necessary to pay attention to the category "Static". The address should be changed to 192.168.1.150. The gateway is standard, you need to see it in the instructions. DNS is better to put 8.8.8.8. This will allow you to use Google protocols for problems with the servers of the service provider.
Access Point Mode
If you are interested in the operation of the DAP 1360 in the access point mode, you need to pay attention to the following recommendations for setting up the device.
You need to go to the browser. In the address bar, write a special combination that will allow you to go to the device settings menu. When the site is loaded, a window will be displayed, you need to specify a username and password in it. They are the same - admin.
In order to perform automatic basic settings, you need to go to the connection menu (it is located under the "Network"). When clicked, Explorer opens. If there is a check mark next to the wireless line, then you do not need to do anything. Click "Next." A new window will open. In it, you need to uncheck the box next to the line that is responsible for hiding the signal name. Enter the network name will be available. Next, you need to select the desired operating mode, namely 802.11 b / g / n. Going to "Security", you should pay attention to the types of encryption. The access point must have WPA-PSK. There you need to come up with a network password.
Work in router mode
In order for the DAP 1360 to work as a router, you need to make certain settings.
It is necessary to go into the parameters and activate the required operating mode of the device near the System menu. If this method does not work, then you can simply go to the section and select “Router” among all available options.
In the "Network" menu you need to pay attention to the WAN line. After completing the instructions, the owner will see that the connection is created. If the provider works with the dynamic address of the PC, then nothing needs to be changed further. Those who receive a signal using other protocols need to open the created connection and delete it. Then you should create your own relationship. In the menu items, you need to specify all the data that the provider will ask. As a rule, customer reviews indicate that there is no need to contact the center directly, since all information is indicated in the contract.
Firmware update
What to do if the DAP 1360 router crashes? Firmware is necessary for the functioning of the router itself; without it, it will not be able to perform basic tasks. Therefore, when it issues a failure, the device either stops responding, or errors constantly appear. In addition, the manufacturer recommends periodically updating firmware versions. This will make your work on the Internet more secure. Consider a firmware update on the D-Link DAP 1360 B1 revision router.
On the manufacturer's website you need to find the necessary version of the software. Pay attention not only to the fact that it was intended for this router, but also for revision. You must download the file to a computer or laptop. You must select the “Service” parameter, in which there will be a tab “Firmware”. There you should click on the "Update" window. Next, you need to specify the path to the file of the new software version. After that, the router will do everything by itself. According to the results, it will reboot.
How to update DAP 1360 router D1 revision? You should, as in the previous case, download the firmware from the official website of the manufacturer. Next, go to the settings and go to the "Advanced" menu. In the "System" will be the item "Update". There, the downloaded file is downloaded.