Modern electrolyzers are actively used in the industrial field. Created these devices to participate in the production of active metals. In particular, magnesium can be noted. This is due to electrolysis. Also, the specified device is able to participate in the production of active non-metals. Of these, chlorine and fluorine can be distinguished.
Motorists also use electrolysis in order to increase the resistance of the metal. In this case, a special protective layer is formed on its surface. It is able to protect the car from metal corrosion . There are various types of models, and in order to independently assemble a hydrogen electrolyzer with your own hands, you need to familiarize yourself with the basic configurations.
Dual Filter Model
It develops this type of electrolyzer for a car with your own hands quite simply. First of all, it is necessary to prepare four sheets of metal. In this case, galvanized steel can be used. At the same time, stainless steel is also suitable for electrolyzers. After that, a container with water is installed directly. The holes in it can be made with a knife. Next, to make the electrolyzer with your own hands, it is important to fix the filters. You can use the usual mesh type.
In the store to purchase it is not difficult. The next step is to fix the check valve. To do this, the container must be fixed on the base. To do this, many experts advise using bolts. Next, it remains to put the board with a thickness of not more than 2.3 mm. The next step is fixed bubbler type tube. It is important to monitor the water level in the container. The last nozzle to be installed. The shutter in this case should be located on the side of the board. The terminals are attached only after the gasket sticker.
Top container device
To assemble this type of electrolyzer for a car with your own hands, you must first prepare the board. Most often they are used in stainless steel. However, galvanized species also come across. In this case, the thickness of the boards should not exceed 2.2 mm. After twisting them with screws, it is necessary to install an insulating lining. All this is done in order to protect the lower shutter.
Next, to make the electrolyzer with your own hands, the upper board is installed. Its thickness should not exceed 1.2 mm. In this case, it is important to install a non-return valve on the protective ring. Thus, water leakage will occur quite rarely. The next step is to fix the container directly. For this, many experts recommend using fittings. The bubbler pipe in the device is attached last. Then install the electrodes with terminals.
Container Bottom Model
To make this type of electrolyzer for cars with your own hands, it is more advisable to choose a plastic container. However, today you can find aluminum modifications. In this case, the device will weigh quite a lot. It is necessary to start the assembly with the installation of the base. This will require only one stainless steel sheet. Its dimensions should correspond to the dimensions of the container. After installing it, it is possible to fix the top board.
In size, it should correspond to the size of the bottom sheet of metal. After that, the tube is installed directly. Filters in this case are optional. The next step is to lock the shutter. It should be mounted directly to the bottom board with screws. It is more appropriate to select them with the marking M6. To date, finding them in the store is quite simple. After that, the nozzle is fixed directly. To this end, many experts recommend installing fittings. In turn, filters are best secured with plastic clips. However, do not forget about the use of rubber gaskets. Otherwise, the insulation of the device will be broken.
Dual valve device
Do-it-yourself electrolyser (drawings are shown below) for two valves is quite simple. AT
The first thing to do is prepare the foundation. For this purpose, it is best to choose a durable sheet of metal. In width, it should converge with a plastic container. After that, the board is fixed directly. At this stage, it is important to firmly fasten all the sheets. For this, you can use screws marked M6. However, much in this case depends on the dimensions of the container.
The next step is to install a bubbler pipe type. Its diameter must be at least 3.3 cm. After that, a shutter is selected for the device. The first valve must be installed at the base of the pipe. To fix it on the inner surface, fittings are used. After that, the clamping ring is applied. Next, to fix the shutter, another metal platinum is installed. Then it remains to fix the second valve to the pipe. The distance from the edge should be at least 2 cm.
Three Valve Models
To make the electrolyzer do it yourself in a three-valve machine, you need to prepare a sturdy plate. Stainless steel in this case fits perfectly. The first valve can be installed directly on the inlet pipe, which is connected directly to the container. After that, the upper plate is fixed. Next, a second bubbler tube is installed. At the end should be another valve.
To fix it, many experts recommend using a clamping ring. In this case, the fitting must be fixed quite rigidly. The next step is the shutter for the device. Only after this is the third valve attached to the pipe and connected to the nozzle. At this point, studs must be used. Also, many experts recommend the use of special rubberized gaskets for insulation.
Galvanized Board Device
Do-it-yourself electrolyser is often assembled with galvanized boards. Today it is very popular. In order to start work, a small-sized plate is prepared. After that, a container is selected under it. You can connect the boards to each other using screws. A total of four units will be required.
After this, you can begin to fix the upper insulating gasket. To quickly carry out the electrolysis process, many experts recommend using only plastic containers. You can fix them on the base with the help of studs. After that, it remains only to install the shutter with terminals for connection.
Plexiglass Model
It is quite difficult to fold the electrolyzer with your own hands from plexiglass in our time. First of all, the problem is that it is very difficult to process. It should also be borne in mind that it is necessary to select a container of the right size for it. In total, four holes must be made in the corners on the board. After that, with an interval of 1.5 cm, metal plates are superimposed. Then you can fix the shutter directly. For insulation, many experts recommend the use of rubberized gaskets, but keep in mind that their thickness should not exceed 2 mm.
Electrode Model
Do-it-yourself water electrolyzer on the electrodes is quite simple. In this case, it is advisable to start the work with the assembly of the bottom of the device. To do this, a small metal plate is prepared. After that, you can fix the shutter. In this case, the container will be located in the upper part. The next step is to fix the tube directly. There are two filters in it. In this situation, a lot depends on the size of the container. After that, it is possible to fix the nozzle.
The next step sets the top sheet of metal. At this stage, it is important to ensure that the plate does not come into contact with the container. In this case, the clamping screws from it must be located at a distance of about 2 cm. The electrodes in this case must be mounted on the shutter. In this case, the terminals are best placed on the other side.
The use of plastic gaskets
You can make an electrolyzer yourself with plastic gaskets if you pick up a good aluminum container. In this case, its isolation will be achieved high. You need to start assembling the device immediately with the installation of the framework. After that, gaskets should be located. At this stage, they must be cut out in a rectangular shape.
In total, four gaskets will be needed to assemble. They must be installed in the corners, and the gap must be about 2 mm. After that, it will be possible to fix the container. For this purpose, take the second sheet and make four holes in it. They are needed in order to fix the container with screws. They are used most often with the marking M6. In this case, for good fixation, it is better to use rubber rings. After that, it remains to install the shutter, as well as the terminals for connecting the device.
Two-pin model
Models of this type must be folded from the base. To do this, you can take an aluminum or steel plate. After that, it is important to fix the plastic container on the cylinders. You can also use screws. Next, it remains to install the shutter. The nozzle in this case can be used needle type. Its diameter should be at least 3 mm.
The terminals in the device are attached directly to the bottom board. For this, ordinary conductors are used. The handset should be installed last. At this stage, it is important not to forget about the clamping ring. Filters for the electrolyzer are best selected mesh type. There should be two valves in the system. They are mounted on spindles.