If you purchased a new TV, it can cause a lot of wires. To hide them in the wall is quite simple. There are several options for this. But before that you need to make sure that several rules are followed. For example, electrical wires should not have insulation damage. In addition, during operation, they should not get condensation and moisture.
In order to eliminate "spurious" interference to the TV signal, the wires should be located as far as possible from power lines and equipment according to the type:
- microwave ovens;
- refrigerators;
- washing machines;
- irons.
This should include other devices that suggest the need to use large inrush currents during operation. If you are thinking about how to hide the cable from the TV on the wall, you should remember that you can arrange the cables in a special channel with low-current lines, among them:
- telephone line;
- the Internet;
- signaling.
Specialist recommendations
It is important to remember that television wiring must be carried out in solid pieces. Crossings of the cable and power lines of the power supply network must not be allowed. If this was not avoided, it is important to ensure the intersection at right angles.
When carrying out installation work, you must use factory-made TV splitters and splitters, because only they will be able to provide reliable wire contact and screening of the input signal. Before you hide the wire from the TV on the wall, you must remember that the twisted wires should not be used. They are not able to provide good shielding, which will certainly affect the signal quality.
How to avoid mistakes
When laying the wires, you must exclude loops, sharp bends and twists into the bay. Soldered wire connections should be used in the panel box, while unshielded sections should have a minimum length, only in this way you will eliminate a decrease in signal reproduction quality. Splitters and cables should be located where they can be easily serviced. These include junction boxes.
If you have a question about how to hide the cable from the TV on the wall, you should know that it can be located along with the power lines. In this case, the diameter of the central wire should be more than one millimeter. It is better to use material with double shielding or a pair of layers of foil under and over the braid.
Laying the wire in the box
The easiest solution to masking the cable will be to use a cable channel or decorative box. Such products are usually made from:
- metal;
- plastic;
- combined materials.
Such a solution has the right to exist for the reason that it complies with fire safety standards, has an aesthetic appearance and is quite easy to install. However, this cable laying option has its drawbacks, they are expressed in the high cost of the product and the lack of recommendations from the manufacturer in the set.
Before choosing a box, you must determine its size, as well as decide which cables will be hidden in it. If you have a question about how to hide the wire from the TV on the wall, then you must remember that when laying the wires in the cable channels, there should be free space inside. It may come in handy in the future.
Do not rush into the acquisition of the cable channel, because you need to pay attention to the transitions for corners, butt elements, plugs, tees and other accessories. She will be able to give the appearance of the box an aesthetic appearance. In addition, the master will not have difficulties with installation. When choosing the described products, it is important to consider their quality. Experts advise to pay attention to the castle. It must open and close manually, you do not need to use additional tools for this.
Cable laying in the wall
The most aesthetic and reliable way to hide the cable will be the solution when the wires are laid in the thickness of the wall. For this, voids are prepared between the drywall sheets and the wall itself. This method is the most common, but sometimes it takes a lot of time to implement it, and in some cases, this technology takes a lot of money. If you installed the TV on the wall, how to hide the wires, you will certainly ask yourself a question.
In order to hide the cable in a concrete wall, you can use the gating method. The process will be quite dusty, and it is suitable only for those who make repairs and parallel cable runs. In this case, it is necessary to decide which wires should be hidden, where they should appear from the wall, and also where the sockets will be located.
The strobes should be laid horizontally or vertically so that you are sure where the wire goes. After all, sometimes after repair there is a need to hang pieces of furniture or a picture. In this case, it will be important not to get on the wire when drilling holes.
Dressing wires for drywall sheets
If you have to hang the TV on the wall, how you can hide the wires, you should think before you begin. To carry out manipulations on decorating wires in drywall sheets, you should prepare:
- GVL cutting knife;
- wire;
- rope or strong thread;
- a nut;
- electrical tape.
Operating procedure
At the first stage, brackets are mounted on the wall for fixing the TV. The angles of its location should be noted with electrical tape, in the process, this will not go beyond the zone that will be hidden. Now the wizard will have to note where the socket for connecting the device will be located. On the surface of the drywall, marking for future holes can be made. The installation area of the outlet must be marked with an accuracy of a millimeter, this will allow you to install it without the formation of voids.
To lay cables in the wall, make cable channels. At the bottom of the wall, another hole is made through which the wire will be hidden in the baseboard with the cable channel. The outlet can be installed behind the TV, but this is relevant only for the case when it is removed from the surface or mounted on a movable bracket. In this case, the outlet will be provided with easy access.
How to hide a wire from a computer
If you want to make the premises of your home more attractive, you should know how to hide the wires from the TV, computer. In the latter case, the cords can be masked under the table top. At the same time, they are strengthened with the help of clips installed on self-tapping screws. If in the future it is planned to move the table, then for this you can use double-sided tape. When you don’t want to spoil the table, you can use the shoe box, having previously originally decorated it for the interior of the room.
If you wondered how to hide the wires in the apartment, we mask the wire using a special cover that you can make yourself. It is perfect for an extension cord into which all plugs will be inserted. If the cord from the speakers constantly bothers you, then you can hide it in the appropriate cover, which is pre-fixed to the back of the table.
Conclusion
Today, a TV is often installed on the wall. How to hide the wires in the interior, many owners of apartments and houses are thinking. As one of the most reliable and aesthetic solutions, gating of holes will be made. An angle grinder can be used for this. It will be necessary to go deep into the surface only by 1 cm. Tile glue is applied to the resulting slit, after which the wire is laid in the mixture and masked with grout for the tile.
If the wall is made of drywall or simply covered with a finish of this material, then you will need to make a rod of thick aluminum wire. It will serve as a broach, because with it it will be possible to stretch the cable or wire behind the drywall on the wall. Many people wonder not only about where to hide wires from the TV on the wall, but also about where to lay communications on the ceiling. The above technique is also suitable for the suspension system, which is most often performed just from drywall.