To connect outlets in the house, you need to understand the types of devices. Additionally, you must have equipment to check the voltage in the circuit. Modern sockets are sold with high-quality covers, they are very easy to connect.
Different types of contacts are used to install models. In order to understand this issue in more detail, it is recommended to consider specific schemes for connecting outlets.
Socket and switch connection
Through a three-channel module, you can connect the outlet and switch. The circuit includes contactors of various types. First of all, it is worth saying that the module is allowed to be installed only through the zero phase. Modern sockets with clips are made with one or more controllers. If we consider the standard model, then the holder is connected through the current plate. In this case, the switch can be installed directly through a conductive contact. In this case, it is important to determine the zero phase. Through an open adapter, do not connect the socket and switch. The circuit for a two-button switch involves the use of a contactor.
Dual Outlet Scheme
The circuit for connecting a double outlet to a 220 V network contains a two-pin module. Directly upper contacts close in the first phase. The tester on the wire should show a resistance of 45 ohms. If we consider the sockets with a contact module, then the socket is fixed on the overlay. The upper contacts are standardly installed in the first phase. The conductive wire is led to the plate. In this case, you need to fix the clamp well.
If necessary, the wire from the terminal can be extended. If we consider the connection schemes of sockets with two contacts, then the dielectric is installed behind the plate. First-order contacts can be fixed on the module. Before starting work, it is important to determine the zero phase and take care of grounding. Some experts advise thoroughly cleaning the adapter. It is also worth noting that it is necessary to check the resistance on the module. If we consider the sockets for two contacts, then the upper wires are fixed on the conductive plate.
Installation scheme for two outlets
The connection diagram of two outlets has a linear adapter. The contacts on the make-up plate are connected in the first phase. It is also worth noting that a tester is used to determine the resistance. The conductive plate is carefully cleaned. The bottom contacts can be connected via the module. Top contacts may only be installed with an adapter.
The conductive wire is stripped and attached with a retainer. If we consider the connection schemes of sockets with double overlays, then the module should be installed with a contactor. Positive module contacts are connected in the first phase. Only then is grounding established. The current-carrying plate must be insulated. The retainer in the connector is often fixed above the adapter.
Connection of a bulb and socket
The wiring diagram for the bulb and socket includes a wired module and a holder with contacts. Directly positive contactors are connected via an adapter. If we consider sockets with a module for three outputs, then the upper contacts are connected directly to the conductive plate. The terminals must be fixed in the socket, and the module must be carefully cleaned.
It is also worth noting that the lamps can only be connected in the zero phase. Particular attention is paid to the resistance parameter. If we consider sockets with modules for two contacts, then the connection occurs in the first phase. In this case, grounding is carried out through the upper contacts. When fixing the outlet, take care of the fasteners of the clamps.
Telephone outlets
The telephone jack connection scheme involves the use of a central node. In this case, models in houses are installed on two or three contacts. If you believe the experts, it is more advisable to tighten the pins last. It is also worth noting that during operation, problems with the expander may occur. The current-carrying plate must be mounted above the cover plate.
In this case, the lead wire is mounted above the adapter. The upper contacts of the outlet can only be connected in the first phase. The holder can be used on two contacts. If necessary, the wire from the module can always be extended. The resistance parameter on the element should not fall below the level of 50 Ohms.
Built-in sockets
The schemes for connecting built-in sockets involve the use of contact modules. The connectors can be used in different sizes. If we consider the sockets on two latches, then they have one holder. The central node in the models is made for two or three contacts. If we consider devices with feed-through modules, then the contacts from the outlet are connected in zero phase.
With resistance above 40 Ohm, the order of the contactors needs to be changed. The holder for the device is mounted above the adapter. It should also be noted that there are models for three contacts. In this case, the lower wires are fixed together at the plate. The central pin acts as a retainer and closes the circuit.
Portable sockets
Portable sockets can be connected via terminal boxes of different conductivity. Many models are made with contactors on wire adapters. The central node in this case has two connectors. It should also be noted that there are modifications to three contacts. Models for them are selected with a dielectric. If we consider simple models, then the upper contacts are connected in the first phase, and the conductors are clamped on one plate. Holders in the sockets are installed under the adapter.
Overhead sockets
Overhead sockets, as a rule, are used at industrial facilities. They have several holders, and the latches are attached directly to the body. Modules in devices are of different types. Modern models are made with linear adapters. The socket connection scheme involves the use of a dipole contactor. To connect the output contacts there is a conductive plate. The upper positive wires of the outlet are closed on the module.
Installing an Internet outlet
The connection diagram of the Internet outlet contains channel adapters. Modules in the connectors are often used with contactors. Some devices are equipped with wide holders. The latches on the models are on the sides. It is also worth noting that the upper contacts are fixed in the first phase, and the resistance in the circuit should be about 55 ohms.
Connecting a power outlet with a loop
Sockets with a loop are allowed to be connected through modules. If we consider the passage expanders, then they have two outputs. Thus, the connection of the conductors is carried out in the zero phase. A fixture is required to secure the module. The central node in models is used with overlays. If we consider sockets with three outputs, then the module will be required with pins. In this case, the retainer must be under the adapter. You will have to use a tester to check the phase.
Installing Outlets
Sockets are very common. Modules and controllers are used to connect devices. If we consider a standard circuit with three outputs, then the holder can be used for two contacts. Additionally, you have to take care of grounding. The upper contacts are immediately connected to the conductive plate. It is important to fully tighten the clamps.
It should also be noted that two-pin devices are often made with terminals. In this case, the closure occurs in the zero phase. It is especially important to note that screw terminals need additional clamps. As fasteners, pins can be used. Sockets with two-wire modules are available in three and four outputs. The central nodes in them can be of various shapes. Experts recommend first of all to determine the positive contacts and insulate the lower wires. Next, you have to check the resistance. Then it will be possible to connect the upper contacts and connect the module.
Triple outlet connection
A triple socket connection scheme involves the use of a linear type module. Two output models can be connected through one controller in the first phase, and the resistance should be about 55 ohms. If we talk about modifications with pins, then the connection can be made only through the central nodes with insulators. In this case, a lot depends on the shape of the plate. You can always use a tester to determine the phase.
Installing a power outlet in the bathroom
Outlets in the bathroom must be installed with a good overlay. Modern models come with wide holders. If we talk about connectors with a linear module, then first of all the upper contacts are fixed. Before that, it is important to find out where the zero phase is with the help of a tester. Additionally, the contacts of the plate are cleaned. Grounding is done at the end of the work.
Many experts say that simple sockets can be used without holders. However, for better insulation of the wiring, they should be installed. Conducting plates should be fixed at the central node. In addition, it is worth noting that new sockets with U-shaped plates are presented on the market. They are poorly suited for installation on linear adapters. In this case, you will have to use thick pads. In addition, two isolators will be required. Contacts are connected in the first phase.
Telephone overhead sockets
Sockets of this type are allowed to be connected through open modules. Many models use a wide contactor. It should also be noted that the devices differ in the number of holders. Modern sockets are available with two clips. If we consider modifications to three outputs, then the upper wires are connected through the first phase. The lower contactors in this case are closing, the maximum resistance on them should be no more than 50 Ohms.
Timer electronic sockets
Electronic sockets with a timer are rarely seen on the market. They are manufactured with a channel module, they can only be connected via terminals. If we consider models with two outputs, then they have only one holder. In this case, the clamps can be installed in different shapes. The electrical connection diagram has double contactors. These devices are well insulated and do not need grounding. The conductive plate in this case passes behind the adapter.
Connecting ground outlets
Earthed outlets can be connected directly through line modules. In this case, it is important to determine the contactor. Additionally, the circuit for connecting wires to the outlet has screw terminals. Many models use a low conductivity dielectric, which needs insulation. Modules for two outputs are connected in the first phase, and their resistance is at least 40 ohms. The conductive plate may be under the adapter.
In this case, the clamps are attached to the pad. It should also be noted that there are sockets with dipole modules. To connect the conductor, you need two holders. The trim must be installed first. When fixing the clamps, the integrity of the pins must always be checked. It should also be noted that the output conductor is often clamped.