Unfortunately, after the repair is completed, many owners of apartments and houses notice that the wallpaper in certain places began to move away from the surface. This problem is especially relevant for joints between canvases. Fortunately, you can solve the problem using modern means, as one of them is glue for the joints of wallpaper.
There are a great many of them on the building materials market today. If you want to make the right choice, then you should consider several varieties of these formulations, get acquainted with their features and consumer reviews about them. So you will be able to understand which mixtures proved to be the best during operation. It is important to first evaluate the front of the job in order to know which tube to prefer.
The reasons for the divergence of wallpaper
To know how to eliminate the likelihood of a discrepancy in the wallpaper paintings before the start of the repair, you need to familiarize yourself with the main causes of this problem. Such complexity is usually encountered by home craftsmen when wallpaper glue does not match the thickness and material of the wallpaper used. Canvases can be too thick or heavy, this also applies to vinyl two-layer material. Quite often, the canvases diverge if the following varieties of wallpaper are used in the repair:
- fiberglass;
- non-woven;
- on a textile basis.
They require the use of highly adhesive glue.
Types of adhesives for joints
If you want to correct some inaccuracies of a wallpaper-paneled surface, then several types of compositions should be considered. Among others, KLEO STRONG should be highlighted. This mixture is a product that consists of polyvinyl acetate and acrylic dispersion, as well as water. Suitable material for all types of wallpapers. After acquiring it, you can immediately use it, as a result, you can get high-quality joints that will not be damaged even because the adhesive is transparent.
You can apply the composition not only when gluing joints, but also when gluing wallpaper in difficult places, as well as to restore peeled sections. Kleo Wallpaper Adhesive can be purchased for only 190 rubles for 80 g. Another variation of the described products is Quelyd Raccord. Its cost is 205 rubles. over 80 g. This ready-to-use adhesive is suitable for vinyl and paper wallpapers, as well as for other wall coverings.
You can use the mixture for gluing borders. On 50 m of the surface, 0.08 kg will be needed. If you still can’t choose the glue for gluing the joints of the wallpaper, then you can prefer the composition “Moment”. It has a pasty consistency, is easy to apply, has low hygroscopicity and is well adjusted. The composition is characterized by high primary adhesion, as well as versatility. To apply glue, it is necessary to bend the edge of the wallpaper, and then apply the mixture parallel to the joint and evenly distribute.
Wallpaper at the next stage is well pressed, and excess glue from the surface of the wallpaper must be removed with a damp rag. Do not start work if the thermometer has dropped below +10 ° C. This glue for wallpaper joints is also good because it has a high adhesive ability, is versatile and easy to use. After drying, it remains completely transparent. During application, the mixture does not spread, and a convenient nozzle of the tube eliminates excessive leakage of glue.
Axton Adhesive Features
This glue for wallpaper joints, the price of which is 188 rubles, is a mixture used for durable and quick fixation of the edges of the wallpaper, if they are separated after repair. The mixture contains special additives that prevent the spread of glue after application. It sets in a short period of time, which is very convenient if the material has to be glued in hard to reach places.
This glue for wallpaper joints, reviews of which are only positive, is supplied in a tube, therefore it is completely ready for use. Its quantity will be enough to treat an area of 10 m 2 . The composition is resistant to moisture and is suitable for any type of wallpaper. Among its ingredients are acrylic polymers and additives.
Features of adhesive for joints "Methylan"
Glue "Methylan" is great for peeled wallpaper. It allows you to connect even vinyl to the wall. It is resistant to high temperatures and is effective when gluing material on plastic window blocks. Therefore, you can use the composition in the niches of central heating batteries. Suitable adhesive for joints Metylan wallpaper for the following materials:
- cullets;
- vinyl;
- non-woven;
- paper wallpaper;
- heavy wallpaper;
- exclusive wallpapers;
- structural materials.
Reviews about the glue "Methylan"
Consumers emphasize that in order to achieve a positive result, it is necessary to use the glue described above under certain conditions. For example, the ambient temperature should not be lower than +10 ° C. Consumers like the low consumption, but the final figure will depend on the surface characteristics. From the instructions you can find out that for each square meter, approximately 100-250 g of the composition will be needed.
This glue for gluing wallpaper joints, reviews of which would be useful to read before visiting the store, is characterized by open time, which, according to consumers, is limited to 10 minutes. This parameter will depend on the surface, application volume and temperature. The composition mixes well with water.
Instructions for the use of adhesive for joints: preparation of tools
If you decide to use glue for wallpaper joints to eliminate defects, you must first prepare all the tools and materials. You will need a stepladder, which is especially true if the joints parted at once in several places of the room. Protection of the room should not be done, because in the process of work, debris and building dust are not formed.
To eliminate defects, it is necessary to prepare:
- construction knife;
- narrow metal spatula;
- thin paint brush ;
- household spray gun;
- a piece of thick cardboard.
A construction knife must have replaceable blades to simplify work. But the metal spatula can be replaced with a ruler. The spray gun should be supplemented with a damp cloth. Do not forget about a piece of cardboard or thin hard material. The size of such a workpiece should be 200x300 mm. You will need a construction hair dryer.
Work order
If you purchased glue for the joints of the wallpaper, then you must take care of the availability of other tools, as well as materials. To achieve a positive result, it is important to follow the work procedure. At the first stage, the damaged area is wetted with water and left until soaking. This will eliminate the likelihood of damage to the wallpaper during operation.
Using a spatula, the finish is carefully peeled off the wall, and with a thin brush you can smear the material from the inside with glue. Cardboard is placed on this section so that the piece overlaps the panels. They need to press the wallpaper against the wall. The included building hair dryer is brought to the cardboard, the surface is treated with a stream of hot air for 20 seconds. After cardboard, you need to remove it to prevent it from sticking, and roll on the surface with a special roller for wallpaper. The base is wiped with a damp cloth and left to dry.
Conclusion
Cloths of wallpaper can disperse if you improperly prepared the surface. Such a problem is observed in those cases when a finishing putty layer was not applied to the wall area. This is especially true for mineral rough surfaces.
Sometimes this complexity arises when the surface has not been sanded or after puttying has not been treated with a penetrating primer. Be that as it may, you can independently fix the problem by using special glue for joints. It is sold in tubes of small volume, so you do not have to overpay.