A fairly important issue for a family of several is the location of the shoes in the hallway. It all starts with the fact that homeworkers try to put their shoes in a ruler, but this does not end with anything, and the mess reigns in the apartment again. But the entrance hall is the face of your home, it is your guests who see it first.
Solution
You can tidy up your shoes, get rid of a pile of sneakers and slippers, which usually fall under the hanger. An excellent way out is to create a stand for shoes with your own hands.
You can also make this design fun - in the form of cute boots that will serve as side racks. Such a piece of furniture will make every guest smile.
Preparation of materials
The stand will have a fairly simple structure, consisting of side walls, between which crossbars will be located. First you need to determine its location in the room. With this in mind, measurements should be made of the depth, width and length of the future structure. If necessary, the product can be supplemented with several levels. The article will consider an example of creating a three-story structure that will definitely not remain idle.
Before you create a stand for shoes with your own hands, you will need to prepare the following materials:
- furniture board;
- round beam;
- shoelaces;
- wood glue;
- cardboard;
- acrylic paint;
- varnish.
The furniture panel must have dimensions equal to 300 x 530 x 27 mm. Instead, you can use chipboard, which is cheaper. However, cutting a complex figure out of such material is not so simple. Chips will not be avoided, but they can degrade the appearance of the stand. For work, you should prepare a round beam, the length of which is 840 mm. Its diameter should be equal to 22 mm. There should be 6 such products.
Tool preparation
You should purchase or find at home the same shoelaces in the amount of two pieces. The length of each of them should be equal to 180 mm. For templates you need cardboard. For work, you will need some tools, among which are:
- electric jigsaw;
- a screwdriver;
- paint brushes;
- a ruler;
- roulette wheel;
- drill;
- felt-tip pen;
- scissors.
For a drill, prepare a drill with a diameter of 6 mm and a drill stand.
Marking and cutting blanks
Using the grid, you will need to transfer the boot diagram to the cardboard. It is necessary to try to reproduce the drawing as accurately as possible, because the coincidence of the holes for the bars in both racks will determine the correct design. A stencil of the boot, which is superimposed on the wood billet, should be cut out of cardboard. The shape is surrounded by a felt-tip pen.
It is important to make sure that the material consumption is minimal when making the stand. To do this, the above operation should be repeated by turning the sheet with another end. At the same time, both boots should fit on one shield. Then you can proceed to sawing parts with a jigsaw. You cannot deviate from a given trajectory.
The template will help to mark the pair of holes on the racks for installing horizontal beams. Shoes on the crossbeams will be inclined. This suggests that one of the beams should be located below the other. At the marked points, it is necessary to make blind holes of 22 mm, the depth of which is 20 mm. This can be done using a drill stand. After that, you can mark and drill 9 through holes for the laces. They should be in every rack. For such work, a drill with a diameter of 6 mm is suitable.
Painting and assembly
Making a stand for shoes with your own hands, you must act consistently. The technology provides for marking the borders of the coloring. Both sides should be decorated. Clear boundaries should be observed between shades. In this case, one zone must be painted and left until dry, only after which you can proceed to the second. The varnish should cover the round crossbars. Apply several layers. After this, the product is left until the drying of the paint materials.
The stand can then be assembled. The first rack is laid on the table, the holes should be directed upwards. The ends of the beams and walls must be coated with wood glue. The beams are then installed in the nests. From above, the element must be knocked out with a hammer, having previously laid a piece of felt so as not to leave marks on the table.
Recommendations of specialists
Once the glue has set, the product can be installed on your feet and lace up your boots. On such a two-tier stand, it will be possible to fit up to 12 pairs of shoes, which is more than enough for an ordinary family. Such a stand for shoes in the hallway with your own hands can be made in the shortest possible time. This saves materials and time. In addition, you can free up free space in the room, which will contribute to the order with shoes.
A more sophisticated stand in the form of an open stand: material preparation
It is necessary to start manufacturing outdoor coasters with the preparation of materials and parts. You will need to cut chipboard, these works are custom-made. All parts except the side wall must be made in a single copy. The latter will have dimensions of 508 x 350 x 16 mm. The top cover must have the following parameters: 900 x 350 x 16 mm. The back wall will serve as a stiffener, its dimensions are 868 x 508 x 16 mm. You will also need a base, its dimensions are 868 x 80 x 16 mm.
The lower and middle shelves will have the same length, it is 868 mm, while the height and depth of the first are 334 x 16, and the second - 279 x 16 mm. The front wall will have the following dimensions: 96 x 16 mm. The length remains the same.
If desired, curly cuts can be made in the side walls, however, it is not worth deepening more than 50 mm. If you plan on making your own cuts with a jigsaw, chips may appear. They can be hidden by stuffing a PVC edging with a mallet. Before you make a stand for shoes with your own hands, you will need to prepare:
- melamine edge;
- plugs for confirmation;
- furniture dowels;
- door hinges;
- confirmation;
- shelf holders;
- wood glue;
- magnetic latches.
Markup
Once all the details have been prepared, they can be marked out. It is important to consider that the front wall and the base will be located 5 mm in depth from the ends of the side walls. The design will be assembled on confirmations. When joining a 16 mm plane, the drilling center will be made with a deviation of 8 mm. Drilling must be carried out from the end and retreat from the edge of the part 50 mm.
When a shoe shelf is made in the entrance hall with one's own hands, furniture dowels are used to fasten the drawer dividers and the front wall. In this case, the middle shelf will be held on the shelf holders.
Drilling holes, working with melamine edges and assembly
After the marking is completed, you can start drilling holes for confirmations, dowels and shelf holders. If chips occur, they can be cleaned with a drill with a pebble. In order not to drill through the workpiece, tape must be glued to the drill.
If you wondered how to make a shelf for shoes with your own hands, the ideas of such products must be considered in advance. An open shelf was presented above, while in this example, something similar to an open stand is considered. Its manufacture is accompanied by the installation of a melamine edge. It will be located at the visible ends. You will need a bay with an edge, a knife, a part holder, an emery block, an iron and a damp rag. But at the assembly stage, it will be necessary to fasten the side walls with a stiffener.
Considering the ideas of shoe stands, you may choose this option. In its manufacture, the next shelf is added to the product lower shelf and base. Details of the boxes are connected with dowels, which are pre-treated with glue. Now the block of boxes and the top cover are fixed to the back wall. Next is the turn of the shelf holder and middle shelf. On this we can assume that the design is ready.
Making a cardboard stand
Quite often, property owners wonder how to make a shoe rack with their own hands. Types of such structures are presented in the article. These products are offered for sale today in a wide range. But if you do not want to spend a dime, you can use the most ordinary cardboard for work. The application of this approach has another advantage, expressed in the fact that it takes more time to make a shelf from chipboard. The design will turn out to be quite roomy and functional, and it will take a little space in the hallway.
The denser the cardboard, the more durable the shelf will be. It must be cut into identical parts, which are folded in the form of a pocket expanding from above. You can fasten such a pocket with the help of a clerical stapler. With its help, pockets are connected into a single vertical shelf. The edges can be sealed with tape or sticky tape so that the stand lasts as long as possible.
If you are interested in how to make a shelf for shoes with your own hands, then you can use the described technology. At the next stage, it remains only to attach the shelf to the wall, and after that you can begin to use it. If the appearance and color of the cardboard remains unsightly, then the shelf can be pasted with self-adhesive film or the remains of wallpaper.
Making a metal shelf
In the manufacture of a metal stand, the choice of materials is wider. You can use one of the options for metal rolling. An additional solution is perforated corners. You can use other metal parts that are designed for other purposes. For example, cable channels or steel cable racks, which are used in the field of communications, are perfect.
If you want to know how to make a stand for shoes from metal with your own hands, then you can use a metal corner, the thickness of which is 3 mm. Furthermore, shelf thickness can vary from 25 to 45 mm. You should not choose metal-consuming material, because it weighs a lot, is expensive and has high strength, which is completely unnecessary here.
You can use a profile rectangular pipe. It has a lower metal consumption, so the wall thickness here is less compared to a metal corner. For racks you can use products with the following dimensions: 40 x 40 mm and 50 x 50 mm. On the crossbars, it is worth taking products 25 x 50 mm or 25 x 40 mm. If you still cannot solve the question of how to make a shoe rack with your own hands, then you should consider a design that will include racks from a profile pipe, and the crossbars will be made of corner. The metal thickness in this case can be reduced to 2 mm, while the width of the shelf will be 25 mm. The corner should be deployed so that the stacked flooring is in the nest.
Making wood shelves
An excellent material for the shelf will be a wooden beam, the cross section of which is 5 x 5 cm. If you want to make the shelf closed, you can sheathe it with OSB sheets. The bar is cut for racks and crossbars. Racks are laid on a horizontal surface and are interconnected by cross members. In the process, it is necessary to use nails or a hammer. Self-tapping screws and a screwdriver will do.
Support frames are attached to the walls through metal plates. Shelves are cut from OSB. They must be installed inside the frame and fixed with screws. On this, we can assume that the stand for shoes made of wood with their own hands was made. Experts do not recommend using the connection with nails, since it can not be called the most reliable. Such fasteners do not hold wood securely, which cannot be said about confirmations or self-tapping screws.