Normal operation of any computer, and especially a device that is more than three years old, cannot be carried out if the system unit is not cleaned of dust and lubricated from time to time. But not all PC users consider this a necessary condition, which is fundamentally wrong. A rather quick consumption of thermal paste is affected by heating of internal elements and, as a result, an increase in temperature in the system unit. Replacing grease does not require much effort or special skills. The main thing is elementary knowledge and utmost accuracy. Next, the maintenance process will be described and, in fact, described how to disassemble the cooler.
Alarms
Any malfunctions manifest themselves as alarm signals. So, before disassembling the cooler, it is worthwhile to find out whether it is really necessary. If there are no obvious signs of a malfunction, then this does not mean that doing nothing is worth it. Sometimes you need to lubricate components for prevention. But if there are good reasons for this, then even more decisive action must be taken.
The main sign that difficulties arise in the operation of the system unit is an increased level of emitted noise. A noticeable hum will cut the rumor, over time it will only become stronger. But it is better not to bring it to such a state and change the lubricant in a timely manner, because a new cooler will cost much more.
Start cleaning
The question "how to disassemble the cooler" is easy to handle. First of all, you need to disconnect the computer from the network and disconnect all available cords. The next step is to remove the housing cover on the left side, while the unit must be carefully placed on the right side. Next, you need to clean the inside of the computer from dust and foreign matter.
Since the cooler works in the correct distribution of air flows, the part, accordingly, takes a lot of dust and small debris from the environment. Most of the unnecessary dust pollution settles on the radiator and other important components.
Cleaning can begin with the most common steps, such as using a conventional vacuum cleaner. But it’s better to finish it more thoroughly - wipe the parts with a cloth moistened with any alcohol solution. You can use both cologne and vodka. Any alcohol-containing substance is good in that it does not react with air, dries quickly and does not cause metal corrosion (which is typical for water). Depending on how thin and deep the cleaning was carried out, the further operation of the computer also depends.
CPU Fan Prevention
You can read more about how to disassemble the cooler below. To carry out this action, you need to remove the processor fan, and then the radiator. They also need to be disconnected from each other. Cleaning of these elements also consists of two stages - surface cleaning with a vacuum cleaner and a more detailed one, carried out using a match.
To ensure further trouble-free operation, you need to touch the surface of the radiator, and its ribs, and the fan wheel, as well as related parts.
Thermal Paste Replacement
The best CPU cooler is the part that is well lubricated. When disassembling a computer, replacing a special thermal paste is very important. To do this, first remove the remnants of the old substance. They are washed off with an alcohol solution. After that, you must wait until the surface has dried well. Finally, apply a thin, neat layer of new grease.
In the event that there is no new thermal paste, and there is a need for its replacement, you need to try to evenly distribute traces of the old substance across all rubbing places.
one system
Many are interested not only in how to disassemble the Acer laptop cooler, but also in the opposite. This is true for those who prefer to apply a lubricant to a single system. In order to do this, you need to find a sticker on the cooler. By removing it, you can carefully clean the fan spindle from traces of grease.
Where the sticker was located, you must also clean it. It is necessary to wipe this place with an alcohol solution and dry it. The next step is to apply a new paste. After that, you can return the sticker back (the original sticker can replace the adhesive tape). Its remnants should not interfere with the operation of the part, as they will create excessive noise. If you do this process accurately, then the efficiency will be maximum. The main thing is to ensure tightness, the lubricant should not leak out due to the increase in temperature.
If you lubricate in this way, then the question of how to disassemble a non-separable cooler will not be a problem.
Power Supply Fan Prevention
During the cleaning process, the user is faced with the question of how to disassemble the cooler of the power supply. First of all, it is necessary to dismantle the component. It is desirable that all manipulations performed with the unit do not require disconnecting the cords from the power consumers. Further, everything happens according to the standard scheme - first, general cleaning with a vacuum cleaner, and then more thorough, with the help of an alcohol-containing substance.
To make a deep and thorough cleansing, you need to rid the unit of the fan. It is necessary to touch all surfaces, fins of radiators and fan wings.
Cleaning the power supply fan is carried out according to the same scheme as the processor cooler. It is necessary to separate the sticker from the surface, under it there will be an end cap. This item must also be removed. Using a normal match, you need to remove contaminants in the form of clots of old grease and dust from the shaft and fan washer.
Then you also need to evenly and uniformly distribute the oil on the cooler spindle. To do this, the fan is rotated - just a few revolutions around the axis.
After completing all the manipulations, the system needs to be assembled: put the plug in place, stick the adhesive tape. In the process, it is desirable to clean and dry the ends of the fan. The ends of the tape are removed, and the power supply is mounted back.
If possible, it is better to save the native stickers, because they contain information about the cooler. This data is very useful if you need to replace it.
It is also important to tighten the cover. If she sits loose, she will create a sound similar to an idle fan.
Silent operation of a computer is an indicator that everything was done not in vain.
Lubricant selection
When cleaning a PC, the question arises of how to lubricate a computer cooler. Experts advise choosing not too viscous mixtures as a lubricant. This is due to the fact that the latter lead to a decrease in the speed of revolutions. The best choice is engine oil. Alternatively, synthetic and mineral oils can be used. Just do not need to apply them at the same time.
Apply a few drops of oil with a match. A match is needed in order to take the minimum amount of substance.
To lubricate the fan:
- WD-40 - anti-corrosion mixture;
- hairdresser tool oil;
- Silicone Grease;
- synthetic car oil;
- mineral car oil.
Cooking grease
How to lubricate a computer cooler? You can prepare the mixture at home. The composition should include graphite and oil. Graphite can be taken from a pencil, it is better to use synthetic oil.
The best cooler
Thus, the best cooler for the processor is the one that the user regularly cares for. The part must be cleaned and lubricated in a timely manner. These procedures will ensure reliable and comfortable operation of the fan of almost any model.
As for the specific characteristics of the best cooler, most of the parts today are made with similar parameters, this is especially true for fans. Of course, there are "game" models that provide good cooling, but their use is advisable only with a high processor load: demanding games, working with several massive programs at the same time, complex processing of audio or video. If we talk about manufacturers, the products of such brands as Cooler Master, DeepCool (an excellent choice is the Deepcool Lucifer V2 model), Thermaltake (for example, Thermalright Macho Rev.A), Zalman (for example, Zalman CNPS12X model) are of high quality.