Means for frying meat can, of course, be purchased in stores of the relevant goods. However, such designs are quite expensive, in addition, sometimes they are completely unsuitable for certain conditions due to excessively large or small dimensions. An alternative option may be an approach that involves the manufacture of such a device on its own. Brazier can be made from a car disk.
Preparation for work
To make the brazier, you will need to stock up on 3 car wheels, nuts and large bolts in the amount of 3 pieces, as well as an 8 mm wire, the length of which is one meter. A rectangular pipe (one meter), as well as 10 mm nuts in the amount of 4 pieces will be needed. It is important to worry about the presence of a welding machine, electrodes, grinder, as well as a mask and welding gloves, which are needed for personal protection.
Material Guidelines
If you decide to make a brazier from a car disk, then it is most preferable to borrow components from an old domestic car of the Zhiguli type. The main condition is solid steel, not aluminum alloy. Today it will not be difficult to find such blanks, it is easiest to do this at tire service, where they can give wheels completely free or at a small cost. If this approach is unacceptable, then discs can be purchased through the online store. Used items cost quite a bit. The remaining components of the type of pipe, bolts, wire and nuts can be purchased at any hardware store.
Cutting discs
If you are going to make brazier from a car disk, it is important to think about how the cutting will be performed. Initially, it is necessary to prepare holes for the bolts, it is quite simple to do this with a grinder. Cutting should be done near the factory holes, doing so in such a way as to save the maximum amount of time and effort. Cut off parts should be discarded, since the brazier will do without them. Now the master must remove the partition, it is easiest to carry out these works using a gas cutter. If only a grinder is available, then initially you need to make an incision, the length of which is 2 cm, moving from a point seam made in a factory. After the partition has been removed, surplus will remain in stock, which can be disposed of with a screwdriver or hammer. This will allow you to get a fairly neat rim that is devoid of septum.
Welding
When making a brazier from a car drive, the next step is to carry out welding work. Disks are set in such a way as to make a solid brazier. An intact disk with a partition should be installed downward, while the partition will serve as a bottom. The second disk, which is already devoid of a partition, must be installed on top. Before welding, alignment should be made, now the discs can be welded around the perimeter.
In order to make the door, 2 vertically oriented cuts should be made so that the weld is located in the central part of the future door. In its lower part, a strip should be left, the height of which is 4 cm. It will act as a threshold so that the coals do not fall out. If you are making a brazier from car wheels with your own hands, then as soon as the door is completed, you should make hinges. To do this, use nuts and bolts. The former are wound onto the latter and welded to the barbecue.
On this we can assume that the door is ready, it remains only to process the edges with a file to remove the "burrs". In the next step, the handle is welded. To do this, a hole is made in the door, into which a large bolt is screwed and seized by welding.
Attaching Carrying Handles
If you are making a brazier from car rims, the photo must be considered before the start of work. In order to use the design was more comfortable, you need to equip it with handles. To do this, use an 8- or 10-millimeter wire. A vice and a hammer will allow you to bend the workpiece in the shape of handles. Nuts are put on the ends of the wire and welded to the body.
Wizard recommendation
In order to avoid pressing the handles to the barbecue and their heating, the ends of the wire should be bent 90 degrees. This will allow you to position the handle so that it abuts against the body.
Making legs
If you need a brazier from a car drive, how to make such a design is described in the article. Now you can proceed to the legs, for the manufacture of which you will need a rectangular pipe. It is cut into three parts, each of which has a length of 40 cm. At the bottom of the disk there are factory holes on the partition, they will facilitate welding procedures and help save time on marking points under the legs. These elements are welded to the holes in the disc.
Conclusion
On this, we can assume that the brazier from the car drive, the manufacturing instructions for which are presented in the article, is ready. The device is compact enough that it can be transported even in the trunk of a car, which cannot be said about factory models, which can be large in size.