Breakdowns of Indesit washing machines happen quite often. Although the technology of this company has always been distinguished by quality, but you must agree, this can happen to everyone and practically any person may have a question: how to change bearings in the Indesit washing machine. In machines of this manufacturer, the bearings are located in the bearing assembly. If at least one bearing located in this assembly deteriorates, then when the drum rotates, amplified noise will immediately be heard. Most often, this can be observed when the spin mode is turned on, when the drum spins at high speed.
Causes of problems with bearings of the Indesit washing machine
When the bearings deteriorate, this indicates that most likely the seals are also unusable, as a result of which water begins to spill through the aforementioned bearing assembly. Although often the opposite situation arises. Due to the fact that the seals fail, water enters this assembly and then malfunctions with bearings arise. It is extremely rare, but it also happens that the drum wipes holes in the tank, after which it is impossible to make any repairs at all.
How to change bearings in the Indesit washing machine? To do this, you need to have strong nerves, a sufficient amount of time and at least a little experience in this field of activity. I must say that if you give the washing machine for repair in connection with this particular malfunction, then they will take a fairly decent amount of money from you, although in fact there is nothing complicated in the repair. Replacement of the bearing and oil seal of the washing machine can be done by hand.
The rotation sequence of the bearings of the drum axis of the device
The washing machines of this manufacturer are designed so that it is not necessary to dismantle the bearings to replace them, which is extremely convenient when repairing household appliances. Replacement of bearings in the all-soldered tank "Indesit" is as follows:
- the back and top covers of the device are removed;
- the belt 1 is removed, which is located on the pulleys of the drum 2 and the drive engine (Fig. 1);
- with the help of a strong metal or wooden rod, the drum pulley is locked, after which the screw is unscrewed, on which it, in fact, rests (Fig. 2);
Initial Process: Get A Taste
How to change the bearing in the Indesit washing machine? The photo clearly shows the sequence of actions:
- A pulley is removed from the axis of the drum (for this, you can resort to the help of a car puller). Given this, you need to know that the pulley itself is very fragile and can be easily broken.
- Four screws are unscrewed and the spacer bar 4 is removed (Fig. 1).
- Four screws of fasteners are screwed (Fig. 3), shifted (taking into account the spirals) and the bar is fixed near the front panel of the SM;
- Two screws are unscrewed, on which load 2 is held, after which it is removed (Fig. 3). This must be done in order to subsequently be able to remove the clamp and the tank cap.
- All cords are disconnected from the thermostat.
Principle of operation
How to change bearings in the Indesit washing machine? Photos show further action.
- Six screws, 4 fasteners are unscrewed (initially, an hour before the start of work, they must be lubricated). The grounding bar 3 is removed. It must be borne in mind that the screws 4 mainly have the property of “souring” in the shell of the bearing assembly. In this regard, unscrewing out is quite difficult, because they can break. There is nothing critical or irreparable in this, they must be carefully drilled and the “thread” of the thread with a tool of the right size (nevertheless, to avoid breakage, the screws can be slightly heated a couple of times and then cooled using a gas burner).
- The connecting screw of the fastener clamp is softened. The collar, a tank cover and a compactor are pulled together. It is important to remember that when the cover is dismantled, you must try not to damage the cord. After completion of work, you must definitely see if gasket 1 remains intact, which must be installed between the cover and the bearing assembly. At the same time, you need to clear the heater from scale.
- With the help of a puller or a proper dowel, the bearing assembly is removed from the drum axis (Fig. 7).
Compression of bearings from unitary enterprise
We look further on how to change bearings in the Indesit washing machine:
- the oil seal is removed;
- wooden sticks are installed on both sides of the bearing assembly;
- with the help of a steel rod, it is necessary to alternately beat the bearings from the base of the bearing assembly with a hammer.
Minimal amount of effort - proper result
What bearings are placed in the Indesit washing machine? Depending on the model of the unit, it can be 202, 203, 204, 205, two-row SKF BA2V.
- Applying instead of the base rod from previous bearings, new bearings are installed. What the bearing assembly should look like with new parts can be seen in fig. 8. Next, new parts must be lubricated with a special tool.
- A new stuffing box 1 is installed on the bearing assembly (bottom figure).
Water leakage through the bearing assembly
Not everyone knows how to change bearings in an Indesit washing machine, and, as already mentioned, water from a tank can flow through a bearing assembly. The oil seal plays a significant role in this process. It must be positioned so that the ring on the spring fits correctly into the depth of the bearing assembly. It is worth saying that there is an incorrect installation of the stuffing box at the factory. As a result, the steel ring on the spring maintains contact with the water in the tank and, of course, undergoes destruction at an incredible speed. The stuffing box ceases to fulfill its function, the bearing unit is immediately exposed to liquid, which has a devastating effect on the bearings of the drum axis.
- the fixed bearing assembly is installed on the drum axis. After that, automotive or any other sealant is applied over its entire area, as can be seen in the following figure.
Bearing Reinstallation Complete
How to change the drum bearing of the Indesit washing machine? Move on.
- Installation is made on the tank cap and the bearing assembly is fastened. It is worth mentioning that the screws need to be combined in several stages, in pairs, obliquely. Then the thermostat and the grounding plate are attached to the cover. Before setting the bar, stripping of the contact pads on the roof of the tank and under the screw of the TEN fastener is performed. This must be done very carefully.
- A lid is installed on the base of the tank, after which a rubber clamp and compactor are applied over the entire area in such a way that the ends of the compactor and the connecting screw are on top of the tank (under load), and not as seen in Fig. 1 (the fifth point is another assembly error at the factory). Tightening the clamp makes it possible to prevent the appearance of bends on the compactor over the entire area of the tank edge and not to run into a water leak.
- The load and strap are installed and fastened.
A detailed step-by-step instruction will answer your main question: "How to change the bearing in the Indesit washing machine."