Configuring the DIR-615 router from D-Link is not such a difficult task and it is up to each user to solve it, regardless of his level of knowledge. This article will provide a step-by-step algorithm for solving this issue, following which you can easily and simply configure your router in 15-20 minutes.
Network Device Specifications
This model of the router belongs to the initial segment. Therefore, her equipment is quite modest. This list includes:
- Wire twisted pair, crimped at both ends, 1 m long.
- The router itself.
- Power supply to the network device.
- Operation manual and warranty card.
The network device has 5 ports for organizing a wired connection. One of them is the entrance. It connects a wire from an Internet service provider. The remaining four are designed to create a wired LAN. The maximum data transfer rate on them is 100M bps. But it should be noted that the speed on the input port will be limited by the provider. In turn, in the wireless part of the computer network, the peak speed can reach 300 Mbps. The device supports the most widespread today Wi-Fi standards: b, g and, of course, n.
Indication and connection
This router boasts a rather interesting design against the background of competitors. Outwardly, it is a black box made in the form of a trapezoid. It is on the trapezoid side that the indicator panel is displayed. It consists of the following components:
- Power LED - indicates the presence of voltage.
- Device search indicator based on WPS technology. It blinks while searching.
- LED for transmitting information from the global web. Flashes continuously during the exchange process.
- The next indicator indicates a connection to the equipment of the Internet service provider. If it blinks or glows, then everything is normal. If it goes out, then there is no input signal from the upstream router of the provider.
- Next are 4 LEDs showing data exchange with devices connected to the corresponding wired port.
On the opposite side of the network device, 5 wired ports are displayed, the Reset, VPS and Power buttons. There is also a socket for connecting the plug from the power supply.
Parameters of Rostelecom
Configuring the DIR-615 router consists of connecting the router and entering the necessary program parameters. Rostelecom (these parameters are located on the INTERNET tab), for example, requires setting these parameters:
- The network address is dynamic.
- The type of connection to the global web is PPPoE.
- Login and password are specified in the contract with the provider.
We leave all other parameters unchanged, and only those associated with wireless data transmission can be set at our discretion.
Values for Beeline Users
“L2TP” - this is the type of connection that the configuration of the DIR-615 router requires in this case. Beeline in this regard clearly stands out from the rest of the providers. The address in this case is obtained from the provider, that is, it, as in the previous situation, is dynamic. The username and password provided in the contract for the provision of data services are also indicated. To gain access to local resources, you need to activate UPnP technology (this check box is set on the ADVANCED NETWORK tab), which is exactly what the DIR-615 router requires in this case. “Beeline” -connection is completely configured after that and you can proceed with the verification.
We configure a router under "TTK"
This provider is much more complicated than in the previous two cases; the DIR-615 router is being configured. "TTK" requires setting a significantly larger number of parameters. First you need to create a connection template in the router with any name (the item "Firewall", sub-item "Virtual Servers"). Then in it we select the interface - WAN. Then we add two types of connections to this template: TCP and UTP. We bind the first of them to port 30001, and the second - 30002. Moreover, we indicate these addresses as the incoming port and outgoing. Also in the protocol parameters you must specify the static address of the personal computer. The router itself is already configured to work with the provider. But there is no PC. Next, we set the exact same static address on the computer that was entered into the profiles of the router. Then install the special program Pulse ++ K. In it we set exactly the same parameters that were entered in the profile of the router. We also cancel the dynamic addressing and set the fixed address of the device. You also need to add this program to the firewall exceptions. Also in this program, check the box opposite the TTK network and select it by default.
UFANET
In this case, in comparison with the “TTK”, it is much simpler to configure the DIR-615 router. “UFANET” -connection requires setting the following parameters in the router (INTERNET CONNECTION tab):
- The device address is dynamic.
- Connection type Russia PPTP (Dual Access). We also set the gateway address rrt.ufanet.ru.
- Enter the username and login from the registration card.
- Set the “Reconnect Mode” flag to “Auto”.
Putting together a circuit
At the first stage, setting up the DIR-615 router comes down to collecting the circuit. First, select the location of the router. Near it should be a stationary outlet, which will provide its power supply. Also, the incoming wire from the provider should easily reach this place. Another important recommendation - the router should be as close to the center of the house, office or apartment. This will significantly increase the coverage area and get almost everywhere a high level of wireless network signal. It is also not allowed to be in the vicinity of the network device of metal sheets. It will dampen the signal and cause interference. A similar problem can occur if there is a microwave or refrigerator next to the router.
And the scheme is going as follows:
- We connect the power supply of the router to the outlet, and the cord from it to the corresponding socket on the router.
- Next, install the wire from the provider with the connector into the port labeled Internet. In a similar way, those network devices that will exchange data using twisted pair cables are connected.
Software configuration
At the next stage, setting up the DIR-615 router comes down to entering the software parameters (they were previously indicated) into the router software settings. To do this, turn on the router and the computer. Then we wait until the end of the loading of each of them. Then we launch any of the Internet browsers installed on the PC. In its address bar, enter the address "192.168.0.1 (this is the address of our router in our computer network) and press" ENTER ". After that, a request appears with the login and password of the router. In the first and second field of this request, enter “admin”. If the router is not new and someone has already used it, then these parameters can be changed. In this case, the entire configuration of the router will have to be returned to the factory settings. To do this, just hold the Reset button for 20-25 seconds. Then we repeat everything again.
After the setup interface opens, we introduce the parameters that were described in detail in the previous sections. Next, we set the parameters of the wireless network - its name, password and encryption method (you must choose WPA2 - it is the most reliable). In the end, do not forget to save everything. After that, it is recommended to restart the router. To do this, just press and release the "Power" button. After that, the router should turn off. Then you need to pause - 10-15 seconds. Next, turn on the router, and after the download is complete, it is ready for use.
Checking Wi-Fi and wired connection
This completes the configuration of the DIR-615 WiFi router and you just need to check the operability of the wired and wireless parts of the local area network. In the first case, it is enough just to launch a browser on the PC and enter any of the addresses. If the start page of the site opens, then everything is in order and you can start testing the wireless method of transmitting information. Otherwise, we check the parameters entered into the router. But on mobile devices, the testing order is slightly different:
- We go into the settings of the tablet or smartphone. In the item “Wireless Networks” we turn on the Wi-Fi transmitter.
- Lists available networks by scanning. We choose ours and connect to it. Do not forget to enter the previously set password.
- Then, like launching a browser, we enter any address and open the start page of this site.
And what do we have?
As can be seen from everything previously stated, the DIR-615 router is not so complicated to configure, and it is affordable for any user, even a beginner. Another indisputable advantage of this router is a high degree of reliability. Therefore, this router is configured only once, and then you can even forget about it.