Marble is an elegant building material. With such a surface, any room looks elegant and sophisticated. But not everyone can afford the marble elements of the interior. However, the same result can be achieved using some technologies that create an imitation of marble. How to create such a surface? Consider this later in the article.
Imitation marble with acrylic paint
First of all, choose a color. In order to simulate a marble surface, you need three shades of paint. The first shade is basic. To select it, you must first decide on the final shade of the surface. To simulate marble in dark shades, select very dark or even black colors as the base. If you prefer a light marble surface, then the shade, respectively, should be light.
In order for the choice of shade to be correct, you need to find a photo of natural marble surfaces and decide which ones are most to your liking. If you consider in detail, you can identify three more distinct colors: the main and a couple of additional. Additional tones should be similar, the first only slightly lighter than the second.
Application of the main shade
To create an imitation of marble with paint using a paint roller, the entire surface of the wall is painted in the main shade. You can start further work only when this paint dries.
Extra shades
Next, you need to apply a couple of additional shades to the surface. At this point, a marble texture is created. We apply the paint of the selected shades to the surface, independently choosing a pattern, with a paint brush about 8 centimeters wide. Alternately apply one shade to the wall, then another.
Shading process
Using a sponge, a plastic bag or both of these devices at once, mix and blend both shades. The final result should look like soft transitions from the first shade to the second, without leaving clear boundaries and obvious traces of the brush.
Imitate veins
Mix the darkest shade of all selected with glaze in a ratio of one to four. With the ready-made solution, we draw veins on the painted surface using a brush with a long, pointed end. We paint with a brush inhomogeneous broken lines, similar to streaks on a natural marble surface.
In the same ratio, mix the glaze with the lightest shade of paint. Gently dipping a feather into the solution, draw it over the surface with a small hatch. If somewhere the lines turned out to be too obvious and noticeable, you can shade them a little with a sponge.
Cover with a protective layer
First you need to wait until the surface is completely dry. If the final result is completely satisfactory, then we cover the surface with colorless varnish to protect the paint and give the surface a gloss similar to real marble.
Imitation marble plaster
Some people think that applying decorative plaster is not at all difficult, and therefore they are trying to do this thing with their own hands. But in reality, not everything is so simple. Decorative plasters can be divided into the following types: Venetian, decorative, imitating silk or velvet, decorative. Each of the categories is divided into several types.
Some of these coatings are very difficult to use, and not even every experienced professional will undertake such a job. To become an expert in the use of Venetian plaster, it will take several years to work with this material.
Plaster requires multilayer application. The number of layers can vary from three to eight. The layers need to be allowed to dry, otherwise, if this is not done, the layers will simply mix with each other when applied. This is suitable for creating a blur effect when one hue smoothly flows into another. When the layer dries completely, a rough edge appears, which is the veins of the marble surface. The application of Venetian plaster occurs in such a way that veins are formed, where one flows from the other. This gives the effect of greater naturalness and naturalness. Considering that this type of plaster needs to be applied in the thinnest layer with a spatula, we can conclude that such an activity is rather difficult.
The choice of textured and decorative plaster depends entirely on what technique the material will be applied. Most often, these materials are quite tough, so you need to masterfully learn how to elegantly apply it so that the final coating looks attractive. Usually, professionals in this matter perform well the application of only certain materials.
Putty simulation
Putty is a material that has versatility and versatility. It is perfect for both home and non-residential premises. Its main advantage is that with its help it is possible to realize any designer's idea. Putty is suitable for a variety of interiors. Imitation of marble putty is carried out in several stages. Consider each of them.
Wall alignment
Before proceeding with the simulation of marble from ordinary putty, first prepare the surface, which should be absolutely clean. In order to level it, any gypsum plaster is suitable. If standard sand-cement plaster is preferred, then you can use it. But nevertheless, it is more convenient to use gypsum mixtures, because they are quick-drying. The wall will completely dry in a couple of days.
Plastering process
To create an imitation of marble, the mixture must be diluted to the necessary thick state, because it should not drain from the wall, but it should not be too thick. The mass is collected in small portions, and smears are applied on the selected wall. Drawing can be the most diverse, including imitation of marble. During the execution of work, it is sometimes necessary to move farther away from the surface, which from afar assess the quality of workmanship.
Sanding the wall
Using a coarse mesh, smooth out irregularities. Do not overdo it. After we remove the dust and primer the wall. Let the primer dry for a couple of hours.
Paint work
The surface is covered with acrylic paint using a roller and brush. This shade is the color basis.
Color application
- Color is chosen according to your own taste. The main thing is that the second and third layers differ in shade brightness. Then it will be possible to achieve the desired effect. The paint is applied in small patches and, until it is dry, part of the shade is removed from the convex spots with a damp cloth. This creates a texture.
Final step
- Lacquer coating can be applied on top to make the wall more glossy, it all depends on personal preferences.