Almost every builder who faced the question of erecting a building for any purpose wondered how to make construction goats with their own hands. Without them, it will be quite difficult to make the mentioned manipulations. The design can be rented, but it is quite expensive, which is especially true for the case that involves the construction of a long time.
Preparation for work
If construction goats with their own hands will be made, then initially it is necessary to prepare all the materials and tools. Among the first, a pipe can be distinguished whose diameter can be equal to 1.5 or 2 inches. The final parameter depends on the expected loads. You will need a pipe with a diameter of 1 and 1.5 inches, the figure will depend on the parameter of the pipe, which was described above. From the workpieces, horizontal jumpers will be made, which will connect the racks. Another pipe with a diameter of 0.5 inches will be necessary for the manufacture of hooks in which horizontally oriented jumpers are installed. A round rod with a diameter of 14 millimeters will act as pins. This workpiece is to be welded onto a horizontal jumper on both sides.
Additional preparation guidelines
If construction goats are made with their own hands, then in addition to the elements described above, an adjustment mechanism will be needed that will help level out surface irregularities. To form it, you need to purchase four bolts, as well as nuts. Bolts should be selected in diameter, the minimum indicator of which should be 20 millimeters. The nut into which the screw is installed should be welded to the bottom of the racks.
Manufacturing technology
When do-it-yourself goats are made, it is necessary to start work on the formation of the pin structure from the racks. In this case, everything is quite simple, at the bottom of these elements you need to weld the nuts for the bolts. A pipe is welded at the top. It will need to be used to mount the section of the next tier. On the sides of the pipe above and below, stepping back from the edges of 200 millimeters, you need to weld the tubes, the length of which is 100 millimeters. There should be four pieces above and below them. As a result, a cross should be obtained, which will allow, connecting the racks with jumpers, to form a rectangular structure. The racks of the upper tiers will differ from similar elements from below by the absence of nuts. In this case, the pipe should remain free.
Recommendations for work
If you make scaffolding, at the next stage, you will need to weld the pins along the edges of the horizontal long and short jumpers, bending them afterwards at a right angle. It is important to provide the structure with a rack that must have components from thick boards. Their width should be equivalent to 0.5 meters. During the assembly process, the rack is stacked on horizontally located short jumpers.
Assembly
When making scaffolding from metal, the next step will be to assemble. For this, the master is recommended to enlist the help of another person. One of them will have to hold two racks, while the other will have to insert jumpers in them. With the help of short elements, you will be able to collect two sidewalls. Each of the masters, holding along the sidewall, begins to insert long jumpers. After these blanks are in place, you can level everything by level, laying ladders on them. Before you make construction goats, you should familiarize yourself with the technology. At the next stage, it involves the possibility of installing subsequent tiers, while you need to use the above method.
Features of the manufacture of wooden scaffolding
If you decide to make goats of wood, then the step between the racks can be equal to the limit of 2 to 2.5 meters. As for the width of the flooring, it should be equivalent to one meter. Do not make the design unnecessarily high, the maximum height limit is 6 meters. To carry out the work, boards with a thickness of 50 millimeters will be prepared. As for their width, this figure should not seem less than 100 millimeters. You can replace such blanks with a square bar of 10 cm. The round pillars can form the basis of the racks and stops. Spacers and fences are usually made of boards, the thickness of which is 30 millimeters or more.
Conclusion
If you want to make folding construction goats, which were discussed above, then they can be used for many years. This can not be said about wooden structures that require processing with certain substances that provide the material with special qualities. Wood serves less and is not so stable in the finished structure. Among other things, wooden wheels should be installed on special scaffolds, which exclude the interaction of lumber with soil. A drawing of construction goats will allow you to carry out work without errors. You can borrow it from the article or draw it yourself, depending on the dimensions of the future building. After all, this will determine how convenient it will be to carry out construction work.