In everyday life, such a problem as a broken door handle often arises. This situation gives people obvious inconvenience - without it, it is difficult to open the door leaf. Repairing a door handle is a rare occurrence. This is explained by the fact that few people know how to properly fix breakdowns in the mechanism. Proper repair of the door handle is completely dependent on the design of the lock.
What types of pens distinguish?
It is important to remember what types of pens exist. Having determined correctly which group a broken pen belongs to, it becomes easy to understand the cause of the breakdown and eliminate it. Distinguish:
- Swivel structures. They are presented in the form of large door handles. In order for the mechanism to begin its work, the handle must be turned clockwise (in some cases, counterclockwise).
- Push. The main difference between such an element from all others is the presence of a lever. When you click on it, the tongue goes down. Repairing a door handle of this type is easy, without additional acquisitions.
What often breaks on the door handle?
The front door is usually equipped with one of two types of handles. There are push, latch, as well as stationary. The first to open the lock by pressing the handle. Stationary mechanically help open the door. They usually have exclusively mechanical breakdowns. Such mechanisms most often do not repair. They buy a new pen and put in place the old one. They are designed as one piece.
At the push handles you can find a variety of breakdowns. Most often, four types of damage are found:
- The handle itself disappears, and the fasteners remain in the door. Such a breakdown indicates a poor quality product. They just change it for a new one.
- In the door handle, the inner square breaks, which simply bursts. After that, the latch cannot be opened. This problem is explained by the fact that manufacturers use such material as silumin in their work. This material is not durable, it often breaks from excessive loads.
- When the latch wears out over time, it may not open. A situation is possible when the outer square sinks. Such a breakdown is reflected in the latch mechanism, because it is this square that plays the role of the handle connector on both sides. This part wears out very rarely. If the square is released with a marriage, then it may break. The defect can be seen, since the square will move to one of the handles, and the second will simply stop opening the latch. Such a breakdown is noticed immediately. It turns out that on one side the handle works, but on the other hand the door does not open. Repair of the door handle in this case is better not to put off.
- After pressing the handle should return to its original position, but in some cases this does not happen. There is a breakdown. Most often, a spiral spring bursts. She can also shift to the side. A defect of this kind is repaired quite simply, but it will take some time.
What is needed for disassembly?
Repair of the door handle always begins with the process of disassembling it in parts. If all the necessary tools are available, then removing it is easy enough. When a person knows the algorithm of actions, he will spend no more than five minutes. You must follow the sequence of steps:
- It is necessary to unscrew the screw, which is located at the bottom of the handle. You should not twist this element to the end, it can be lost due to its small size.
- The main fasteners of the handle are usually hidden under a decorative trim. Need to remove this pad. It must be twisted counterclockwise. For this work, no tools are needed, the part can be easily unscrewed manually.
- After removing the pad, you can see the fixing system of the handle. Usually it consists of self-tapping screws. There are times when the system is attached by screw ties. Unscrew the fasteners with a screwdriver, which is at hand.
- The next step is to remove the pen from the desired square.
How to remove the handle, which is presented in the form of a large lining?
It happens that on the front doors put handles that look like a large overlay on the door. To remove such an element, you must perform the following steps:
- Screws are located at the edges of the door trim. They must be unscrewed with a screwdriver. The handle should be removed along with the pad. If you unscrew the screws on one side of the door, the handle will be removed on each side.
- When the old part is removed, then you can begin to install a new one.
Removing the handle is a fairly easy process. If you follow the instructions step by step, then there should be no problems.
Installing a new pen is also a simple process. It is necessary to perform all actions to remove the door handle, only in the reverse order. An important nuance in this case is the choice of a similar product.
How to repair the handle on the front door?
Repair should begin with a breakdown. Often there is a situation where the handle falls off, and its base is still in the door. In this case, the lock ring is most likely damaged or dropped out of the lock. It is easy to put in place, with some effort. Repair of the door handle of the entrance door is carried out in the following order:
- From the front door you must remove the handle, which is still on it. The circlip should also be on the door leaf. If it is not damaged, then you need to connect the elements of the handle and put the ring in its original place. After carrying out such actions, you need to put the handle in place. Often, the circlip breaks, then the question arises of acquiring a new locking element. This decision is made when the ring is bent. It occurs that it bursts.
- It happens that the square that is inside the handle bursts. This occurs when manufacturers save on this element, making it from fragile material. When it burst under the influence of loads, it will have to be definitely changed. When buying a new accessory, pay attention to the steel handles for the entrance doors. We can say that the repair of the door handle of a metal door is similar to a regular one. First check the square. It is necessary to find out whether it is in working condition or not.
- For some people, it happens that the latch does not close with the working handle. Usually, such a defect in the operation of the mechanism appears if the square is shifted to the side. In this case, the square was made short. You must remove one of the handles. A handle from any door will do. Then they pull out a short square. In place of the deleted item put a new one. It is important to put everything in its place after completing the replacement.
A new square can be found in the local market. Usually they sell long models that need to be customized to the required size. You can do this kind of action yourself. To do this, you need a grinder. If there is no such tool, then you have to work with a hacksaw for metal.
What to do if the handle does not return to its original position?
Repair of the entry door handle is required when it does not reach its original position when the door is closed. The reason most often lies in the bursting coil spring. It is repaired by analogy with a lock ring. It is necessary to remove the handle, replace the spring. The spring is usually fixed with a special washer. In turn, the circlip locks the washer. In the market, as well as in specialized stores, it is difficult to find this element for sale. Therefore, most often you have to buy a new pen and put it in place of the old one.
Repair Tips
Repair of the door handle of the entrance metal door is carried out by analogy with the accessories of interior doors. Failures are most often similar. The main thing in this case is to understand the cause of the breakdown. To find out which element of the door handle is out of order is possible only after the handle has been disassembled. Almost any person who has the skills to work with tools can repair an item.
The highlight is removing the handle from the mounts. It is important to know how this device works. You need to find out which of the elements performs any specific function. After the design itself becomes clear, it will be clear how to carry out repair work.
Snap handles
Repair of the doorknob of the interior door is often enough required in everyday life. At some point, the mechanism fails. This happens if the latch handle is used for a long period of time. Many people think that this kind of mechanism is not being repaired, but it is not.
Repairing a door handle with a latch is a standard procedure for people living in apartments. It is important to start the repair at the first manifestation of a breakdown. Then there is a chance that you don’t have to change the entire handle. It happens that the latch sticks. The movement of the crossbars is limited when the door closes, the same thing happens when you try to open the door. Frequent damage is the immobility of the tongue. When a person presses the interior handle, the mechanism does not come into action. The tongue begins to periodically sink; it is becoming increasingly difficult to get it.
Conclusion
So, we found out how to repair door handles of different types. As you can see, the operation is not too complicated. In extreme cases, the element can be replaced entirely.