It would seem that it could be easier than connecting a router to a computer? Just a couple of minutes. But sometimes the result can be completely unexpected, for example, the computer does not see the router, and it is impossible to enter the settings of the router settings. What to do in such a situation? Those who want to try to fix the problem on their own are further offered some simple tips. But first, a few words about the possible causes of the failure.
Why the computer does not see the router: possible reasons
As for the reasons, there can be a lot of them, from a banal incorrect connection to equipment malfunctions, including the router itself, and the corresponding ports on the computer (physical breakdowns or software failures of the device itself will not be considered in detail).
However, the main assumptions that the computer does not see the WiFi router, depending on the situation, are considered as follows:
- wrong connection;
- Incorrect access settings
- lack of network card drivers;
- inoperability of the Wi-Fi module;
- hidden network.
Based on the foregoing, further, we will consider each solution separately.
What to do if the computer does not see the router with a direct connection?
Let's start with the situation when the user tries to connect to the router for the initial configuration through the cable directly. It seems that all the cables are connected correctly, but still there is no connection. Well, the router does not see the computer, even though you crack. What to do
First of all, if you are sure that all cables are connected correctly, check if the address of the router itself is entered correctly in the web browser. In most cases, it is 192.168 with the last two digits 0.1 or 1.1 (for some non-standard models other addresses may be used).
The address for entry can be found on a special plate, which is located on the back of the device. There is also a username and password that must be entered when entering the settings.
If everything is entered correctly, but the router is not visible, a regular reboot of the router may help by pressing the On / Off or Power buttons for 10-15 seconds. However, it is best to disconnect the router from the mains completely, maintaining the same interval. If, after this, the computer does not see the router, you can try to reset the router to the factory settings. To do this, there is a small hole in the bottom of the case, in which there is a barely noticeable Reset button.
Checking the connection
If the previous actions did not take effect, you should check the correctness of the direct connection.
Try plugging the network cable into another slot on the router or doing the same thing on the network card of the computer. If this does not work, perhaps the cause is damage to the cable itself. In this case, just replace it and try entering the settings again.
Connection Diagnostics and Ethernet Port Inspection
Also, the situation when the computer does not see the Wi-Fi router may be due to damage to the ports themselves. As already mentioned, use a different port or “ring” the one to which you are connecting.
However, the reason may also be in the network adapter. In this case, you should make sure that all the necessary drivers are installed for it in the system (and correctly). If the device in the corresponding manager is marked with a yellow icon with an exclamation mark, the drivers must be reinstalled. Also, as an option, you can use the complete removal of the device, followed by a reboot of the system when the driver is installed automatically. In the case of non-standard equipment, you must use the original disks or specify the location of the driver installation file on the hard disk manually.
To obtain more detailed information, it is necessary to carry out a connection diagnostics. It is performed from the adapter settings section, which is located in the network connection menu located in the standard “Control Panel”. If problems are found, the system will notify you of their resolution.
Verify Network Attributes
Finally, the reason that the computer does not see the router when using a wireless connection may be the network hiding set in the settings.
In this situation, you need to connect to the router directly through the cable, enter the wireless settings and uncheck the SSID broadcast enable line (for TP-Link models). In other devices, this may be the point of hiding the network name, installing just hiding the network (SSID), or something like that. After that, it is desirable to reboot the device in the manner described above. In addition, it would be nice to restart the main computer system (as they say, you never know).
Conclusion
In most cases, the above methods help fix the connection situation. If none of these solutions helped, so as not to replace the equipment, it will be necessary to reflash the device. Doing it yourself at home is quite problematic, so it’s best to contact a service center. If such actions do not give a result, you will have to make a complete diagnostics of the router, not the subject of malfunctions, but if they are detected, replace the device.
But, as practice shows, the most common is the incorrect input of addresses and parameters when entering settings, breakdowns of cables and ports, the absence of network card drivers and wireless modules, as well as the settings for hiding networks. So at least one of the proposed methods will help.