In stores today there are various lampshades for the chandelier. With your own hands, however, such products can be performed quite simply. As a result, it will be possible to get a very original solution that cannot be found in any other interior.
Making a lampshade from cardboard
For work you will need a thin white cardboard, glue gun, fishing line or thin twine, an office knife that can be replaced with scissors, round-nose pliers, as well as wire for the frame.
Features of the work
DIY lampshades for a chandelier can be made quite simply. To do this, you need to prepare all of the above materials and tools. After that, the master will have to determine the dimensions of the product. In the example, a diameter of 30 cm will be considered. This indicates that for manipulation it is necessary to prepare cardboard, the length of which is 90 cm.
First you need to make a frame for which a piece of wire is cut. The latter must be given a length within 98 cm. From this blank, a circle with a diameter of 30 cm should be rolled up, fixing the ends with pliers. Next, 3 hanging elements are cut from a fishing line or twine. The length of the pieces should be measured taking into account the height at which the lamp is supposed to be suspended.
The three elements prepared in advance should be wired in three places. When fixing, the elements are distributed evenly. If you make lampshades for the chandelier with your own hands according to the described technology, then on the cardboard in the next step you need to depict butterflies of different sizes, and then cut them out. Now the cardboard is folded in the form of a cylinder, the joint is glued with thick paper or stitched with a stapler. The upper part of the lampshade must be fixed to the wire. To do this, it is recommended to use a piece of thin wire or glue.
Final work
When making lampshades for the chandelier with your own hands, it is important to observe the technology of the work. Only in this way will you be able to achieve a positive result. If the joints and incisions are not very aesthetic, then you can decorate them with butterflies. Such a lamp can be used both in the children's room and in the bedroom. Instead of butterflies, you can cut flowers, snowflakes or stars - in general, everything that comes to your mind.
Back to USSR
If you are thinking about how to make a lampshade for a chandelier with your own hands, then you can plunge into the memories of the sixties. In those days, floor lamps, which were made in the form of a cylinder, were especially popular. For such work you will need a decorative braid, knitting hook and scissors. Choosing the first element, you need to combine colors to taste.
Technology of work
Before you make a lampshade for the chandelier with your own hands, it is recommended to make a sketch. After you can begin to work. To do this, you need a frame that can be borrowed from the old lamp, the first braid should be tied to its lower part. The tail should have a length of 5 cm. The braid should be pulled onto the upper ring from the outside, throwing and stretching through the lower ring, or rather, its inner side. These actions should be alternated until the next sector of the frame begins.
If you are making a lampshade with your own hands for a chandelier, then the tape should be fixed at the next stage. Next in the case is a braid of a different color. It should be knitted to the next sector, not forgetting to leave the tail. The third sector is filled in the same way with the remaining tape. Ponytails should be pulled from below using a crochet hook. On this we can assume that the ceiling of the 60s is ready.
Fringe and braid lampshade
If you decide to make a lampshade with your own hands for a chandelier, then in the process of work you can use fringe, which will form the basis of a rather interesting idea. Before starting work, it is necessary to prepare two steel hoops or use an embroidery hoop. The craftsman will need a fishing line, glue gun, braid with fringe and acrylic paint. It should match the color of the tape. You will need scissors.
Manufacturing technique
Before making a lampshade for the lamp with your own hands, the hoop or existing hoops must be painted with acrylic paint. While the composition dries, it is necessary to make 3 marks on the rings, placing them at the same distance from each other. Now you need to cut three pieces of fishing line. They need to be tied to a smaller ring, leaving the upper ends with a margin, so as to tie in the subsequent lamp.
Now the master must determine the length of the fringe by taking 2 cm from it. The line should be tied to the second end to the obtained length. This will allow you to get a cascade. Now it’s the turn of the glue gun, with it you will need to fix on the lower ring. The same manipulations must be done with the upper ring.
It is important to note that fishing line can melt under the influence of glue, so it must be applied so that the materials do not interact while the composition remains hot. Glue for this is applied to the paper, it waits a certain time, only then you can start fixing.
Alternative lampshade solutions
If you want to make a lampshade for the chandelier with your own hands from fabric, then you can use one of the above technologies. This is especially true for the latter option, when the fabric is tuned to a pre-prepared strip, and then cut so that it was possible to obtain strips hanging down. However, it is not necessary to start work from scratch if you want to create a beautiful lampshade. For example, you can use a paper flashlight, complementing it with shapes from chocolate assortment or cupcakes. The latter are glued to the base of the flashlight, which allows you to get a new lampshade design.
Conclusion
If you decide to make a lampshade with your own hands for a chandelier from threads, then you can use, again, the above technology. The threads are sewn onto a pre-prepared strip, the length of which corresponds to the size of the hoop. The threads can be different in color and length, which allows you to get an unsurpassed effect.
For work, a paper shade can also be used, which is complemented by pendants. Glass jars can also become part of the lampshade. To do this, they are painted with paints, and, if possible, decorated with engraving. If in one of the rooms of your house the hi-tech style is maintained, then you can use cans that you don’t even have to paint.