Parquet board is often used to finish the floor, because it is considered an environmentally friendly material. Although over time, his condition may worsen. Due to prolonged or improper use, the shine leaves, scratches and other defects form.
To avoid damage to the flooring, it is worthwhile to understand how to care for and use it. Prevention and a minor upgrade will benefit. When serious deformations occur, there are many ways to restore the original shine and beauty. At the same time, it is not always necessary to call a wizard - you can cope with the task yourself. How to upgrade parquet? The answer to this question is below.
To restore its former shine and beauty
Updating parquet without looping is not as difficult as it might seem at first glance. Before starting work, you should understand what are the reasons for such deviations. Most often, it is improper care that leads to scratches and the coating loses its former appearance. So that after recovery there are no repeated flaws, you need to follow simple operating rules:
- It is worth every four weeks to process the entire area with wax or special means. More attention is paid to places with active movement of people.
- There are special spray varnishes. They are suitable for those areas where burrs have already appeared.
- There are funds for the return of shine - they can be used once every 14 days.
- When the floorboard is not too thick, the care should not be wet. Or oil or wax is taken as a basis - such a composition helps it to last longer. Processing - once every two weeks.
If you follow these rules and perform basic care procedures, the service life is doubled. Those people who choose this particular finish should understand how this is done.
How to remove minor flaws?
Minor changes on the surface of the floor are cleaned the easiest. The simplest method is grinding. The simplest process is a special machine, not everyone has it, so sandpaper will help. Using paper is not so simple, but there are simple recommendations that can speed up this process:
- It is necessary to stick sandpaper of different grain sizes on any comfortable shoes.
- When it sticks, the shoes are put on their feet, after which you just need to scuff around the parquet board on the floor.
- When the work is done over the entire area, waxing is used.
If the floor is with a new finish, then prophylaxis is performed immediately (once a month). For the old one, this procedure will have to be done more often so that it does not deteriorate at all. This procedure is simple and does not take much time.
Can I use putty?
Experts believe that it is not necessary to carry out grinding - you can resort to puttying. Most often, this option is suitable in cases where there are serious violations of the integrity of the surface. The principle of the method has some nuances:
- You need to buy putty in parquet color.
- Then spread the restoration paste on the surface.
- When everything is dry, the coating is treated with fine sandpaper.
- After this, you need to wax the floor (grate it).
To parquet acquired the old external data, you need to create the joints of the board. There is a simple method for this:
- To work, you need an awl and a ruler.
- Using a ruler, make pressure at the joints (a seam should result).
- Fake pins are created with an awl, making longitudinal stripes, exactly according to the ruler.
- Now you need to perform coverage. For this, water-based parquet varnishes are used. They are safe and effective in such work.
In order for the coating to be reliable and of high quality, varnish is treated twice. Once everything is dry, it is worth using wax for rubbing. As you can see, updating the flooring is quite simple. All of these procedures are beneficial and gloss the floor.
How to deal with serious problems?
Before fencing parquet, it is worth assessing the complexity of the work in order to choose an effective method. With a long and incorrect period of operation, the boards diverge. Many people think that such a topcoat has to be dismantled and a new one laid. There is always a solution for such a problem:
- You can drive small nails at an angle of 45 degrees into each board.
- To deepen these fasteners, use a special rod or something similar.
But sometimes not one die fails, but a whole perimeter. What to do in this case? Before updating the flooring, it is worth setting up special bamboo inserts. They will go out. To trim them, use any sharp object. Places of such additions can be wiped with a putty compound and masked with wax.
How to update an old parquet? When this question arises, one has to pay attention to the general condition. The reasons are very different. Sometimes nothing is visually noticeable, but there is a slight creak or any other sound. There is no need to invite the master, because many work options are performed independently.
Sounds when walking
Oddly enough, it is the appearance of a squeak that is the most common cause. The boards are drying out. Before updating the parquet with your own hands, you need to determine the places where such deviations are present. Sometimes, even with proper use of the coating, an unusual sound appears. Leaving aside this situation is not worth it.
Of course, there are such cases when it is not possible to remove the creak, because initially the base was not leveled. In such a situation, it is necessary to completely dismantle and level the rough concrete floor. Although this can be avoided. How to upgrade old parquet without looping? You will need to make wedges and mount them on the floor around the perimeter.
Sequence
This procedure is simple, but the basis is to choose any available instruction and stick to it:
- The room should not have high humidity, otherwise it will not work to create the required conditions. This indicator should not exceed 50%.
- The skirting boards are dismantled and only after that they begin to wedge.
- If old wedges were installed, they are removed.
- At a distance of about 40 centimeters, they are laying out new ones.
- Then, for 7 days, it is worth periodically sealing the inserts, while checking the surface for creaking.
When this period of time is not enough to correct the situation, the reason lies in more serious deviations. You have to carry out a complete dismantle or put up with the presence of such a sound. It is believed that the simplest task is to update the varnish on the floor. After a little time during operation, it "leaves" in places of active movement. To eliminate such a flaw is easy.
How to update the varnish?
For this, they acquire a special composition. It is better that it is water-based - it is completely safe and has decent qualities. Although many experts believe that there are such coatings, after which water-based products cannot be used. Therefore, it is necessary to establish what the parquet board is processed with.
Work can even be done independently. To do this, the surface is cleaned of dust and other contaminants. Then you need to degrease the surface and remove any burrs. In the process, it is worth carefully evaluating the gender. If any chips and other flaws are present, then it is better to remove them immediately. Make it easy.
What next?
Next, any tool is selected - a roller, a brush, but it is better to use two at once. It’s easy to apply any composition to the surface with a roller, and with a brush it is easier to get to hard-to-reach places. Varnish is applied over the entire area, you need to wait until it dries completely. To restore the original shine, you have to cover in two layers. The second is applied after the previous one has completely dried in a thin layer.
How to upgrade parquet at home? Answering this question, you need to know that after each procedure you need to cover the floor with varnish and rub with wax. Without such actions, it is difficult to give it beauty and original ideality.
Conclusion
So, now we know how to update parquet at home. With any minor defects, it is quite possible to give the finish a perfect look. Experts recommend that you follow simple rules and not use unusual options.