Do-it-yourself floor clothes hanger can be easily made. It is often used not only in residential apartments and houses, but also in offices. Of course, such an item can be purchased in the store of the relevant goods, but quite often the cost of the hanger is high and not all models are suitable for color and size. This item is an excellent solution for a hallway that does not have enough free space. Similar designs, which can be purchased at the store, most often have two sides for free access (out of four). There is no such hanger-hook for clothes; it is easier to acquire and strengthen it. Often, in its manufacture, accessible hooks are used that are located as close as possible, this subsequently complicates access to the other sides. In the end, the floor hanger is loaded on one side, which quite often causes it to fall. This is due to the fact that the design has a too high center of gravity. You may have noticed that not all hangers have hooks for hats and bags. That is why you can come up with your own design, taking into account all the shortcomings of factory products.
Preparation of materials and tools
Do-it-yourself floor clothes hanger can be made by any novice master. However, initially it is necessary to prepare a set of tools and materials, among them: screws, sandpaper, chipboard, swivel mechanism, confirmations, a jigsaw, as well as an edge.
Design Features
So, your choice is a floor hanger for clothes. Having made it yourself, you can save money, because the models presented in stores are quite expensive. However, before starting production, it is necessary to develop a design project, while you should consider the problems that were described above. This will allow you to get a hanger, which will differ in functionality and ease of use. The base of the product will be hollow parallelepipeds, which must be installed on the basis of a rotary type. It has two planes. The swivel mechanism should be between the support bases, which are located below. You can purchase accessories in a specialized store. The mechanism should have bearings that will provide rotation under load, the weight of which reaches 110 kilograms. The support base in the upper plane can be rounded, for this a jigsaw is used.
Parts preparation
If you will make a floor hanger for clothes with your own hands, you will need to initially prepare the parts. The design is assembled using chipboard, the thickness of the material should be 16 millimeters. The color is selected depending on the characteristics of the interior and other pieces of furniture that are in the hallway. When preparing parts, it is important to observe right angles, so experts advise to order cutting of elements from professionals, but gluing the edges can be done independently.
Edging
Before you make a clothes hanger, you should learn about how to glu the edges. It has an adhesive base and can be melamine. Its thickness is 0.5 mm or less. The edge is applied to the end of the element, while the adhesive base must be facing down. Then it is ironed, which should not be heated. Until the edge has cooled, it is smoothed using a dry rag. The next step is the processing of the ribs, the excess edges will need to be removed with the help of sandpaper and a sharp knife.
Workpiece sizes
In order for you to get a hanger on casters for clothes, you will need to prepare the bottom base of a square shape with a side of 560 millimeters. The top base should have a side equivalent to 380 millimeters. The side elements of the lower part are made in the amount of 2 pieces, the dimensions of each should be 600x300 millimeters. All other parts are performed in an amount of 2 pieces, this applies to the inner side elements that make up the bottom. The dimensions of each given workpiece should be equal to 600x267 millimeters. The upper and lower parts will be square with a side of 267 mm. Similar parts are manufactured with a square side of 167 millimeters.
Side elements should have dimensions equal to 1200x200 millimeters. The lateral inner parts of the top have dimensions that are 1200x167 millimeters.
Assembly
A metal clothes hanger can be purchased by you in a store - this is easier to do than to make it yourself. But if you decide to make your own floor construction made of wood, then for assembly you need to use confirmations with dimensions of 50x70 millimeters. For them, pre-prepared holes located at the ends. To do this, use a 5 mm drill. The depth of the holes should be 60 millimeters. The holes in the plane should have a depth equivalent to 8 millimeters. Make them necessary through and through. No need to fear that the fastener heads will be visible - then they can be hidden using plugs. You can make and do-it-yourself wall hanger for clothes. To do this, prepare the bar from the chipboard, several hooks and fasteners. All these components are interconnected, and after the construction is hung on the wall. In the case of the floor construction, everything is different. The hanger will spin due to the presence of a rotary mechanism, it is fixed with 4x16 mm screws.
Work Tips
The rotary mechanism has an integral structure, and its fastening to the base is done by creating technological holes with a depth of 10 millimeters. Initially, markup is to be done. After the hanger is assembled, the fasteners will be hidden by the upper plane. The hanger can be equipped with different hooks. Thus, the upper ones may be longer, which will allow them to be used for hats. The middle ones are intended for children's clothes, but as for the lower ones, then it will be possible to place bags on them. The design is stable due to the fact that the center of gravity moves closer to the floor surface.
Alternative option
A wall hanger for clothes in the hallway can also be made by you. To do this, you need to prepare a board, timber, as well as hooks. The board should have the following sections: 25x150, 50x100, as well as 25x80 millimeters. As for the beam, it should have a square section with a side of 100 millimeters. A bar will act as a base, which is marked with the necessary length and cut off. If the hanger is not wall, but floor, then legs should be attached to it. The design is necessarily processed by sandpaper. If legs are provided, they should have a length that is 350 millimeters. The legs on one side are cut at an angle of 45 degrees, which will add aesthetics. On their edges there should be supports which are fixed. These additional blanks are cut from the board, the cross section of which is 25x80 millimeters.
The legs can be strengthened with elements of 330 millimeters in length. These blanks are made of 50x100 millimeter boards. There should be four of them. When a wall hanger is made in the hallway, the upper part can be made more elegant by decorating with a decor that is made of a 5-centimeter board. The lumber goes to the cutting of the square, which is screwed to the upper part of the base with the help of two screws. The workpiece is strengthened with fittings, however, if you want to make a decorative element yourself, then it should be deprived of fasteners for screwing. The blank in this case is glued using a joinery.
Final work
When clothes hangers are made in a cabinet, it is important to provide high-quality fasteners. Quite often, not only mechanical, but also adhesive methods are used. In the latter case, both surfaces should be lubricated with wood glue. After this, the structure is left until the composition completely dries and only then can it be treated with varnish or stain. The mixture is applied in several layers, between each of which the product should be left until completely dry. After the surface is treated with sandpaper. Before you start applying the next layer, the surface must be wiped with a damp rag. In the manufacturing process of the clothes hangers in the closet, the above technology can be used. However, no matter what design you choose, if it is based on wood, all corners must be cleaned, the same applies to the ends of the structure. You can do this between applying layers, then the surface will gain the effect of antiquity.