Corrosion protection of metal structures and industrial structures is a good reserve for the future, this allows saving on operation and repair of structures. As such a tool is “Tsinotan”, the technical characteristics of which will be described below.
This anti-corrosion composition provides protection even in conditions of high pollution by industrial emissions. You can use the composition in all microclimatic regions, types of atmosphere and categories of accommodation. The coating is resistant to contact with petroleum products and oil, sea and fresh water, as well as aqueous solutions of salts. You can use Tsinotan as an independent coating or as a primer in combination with other materials.
Specifications
“Tsinotan”, the technical characteristics of which must be studied before purchasing the product, is gray, the shade is not standardized, and the dried coating has a matte surface. The thickness of the dry layer can vary from 40 to 80 microns. Impact strength is 50 cm, adhesion is 1 point.
The bending elasticity is 10 mm, and the heat resistance of the coating is 150 ° C. “Tsinotan”, the technical characteristics of which will be of interest not only to professionals, but also to the general consumer, has a thixotropic viscosity in the range of 2, 9-3 g / cm 3 . The mass fraction of non-volatile substances varies from 86 to 88%. Consumption for a single-layer coating varies from 195 to 390 g / m 2 . Up to grade 3, the layer will dry within 2 hours, while the temperature of the environment can vary from 20 to 22 ° C, relative humidity can be 65%.
Main features and properties
Application of “Tsinotan” is possible without seasonality restrictions, while the external ambient temperature can vary from -15 to +40 ° . The composition is completely ready for application, which indicates ease of use. The layer is resistant to aggressive environments, in addition, it has a high service life.
It is possible to use Tsinotan for corrosion protection of transport structures and bridges, chemical and oil and gas industry facilities, as well as metallurgy. The composition is compatible with some compositions of the Ferrotan type, and it can be used with epoxy, acrylic, polyurethane and vinyl substrates.
Instructions for use: surface preparation
"Tsinotan", the technical characteristics of which you should be aware of before using it, is applied to previously prepared substrates. The latter should be degreased, and then carry out abrasive cleaning to the second degree. The surface should be rough, and if we are talking about hot rolled steel, then manual or mechanized cleaning up to 3 degrees is permissible. On a smooth surface, application without roughening is not allowed. The base must be dusted before using the mixture.
Features of use
Primer "Tsinotan", the technical characteristics of which were presented above and will help you avoid mistakes during the work, is a composition that should be mixed well until smooth. If necessary, the mixture is diluted to a working viscosity before use. In the field and factory conditions, the application should be carried out at the recommended temperature range, and the relative humidity at the time of application can vary from 30 to 98 ° C.
If it is intended to form a multilayer coating, then each subsequent layer should be applied after the previous one has dried. It is necessary to wait for the tack. You can check it by pressing your finger on the cover. If there is no trace left, then you can continue to work. There should be no stickiness. The composition should not be in contact with air for long in an open container.
The technical characteristics of the Tsinotan coating indicate that the subsequent application of coating layers of the compositions, varnishes and enamels should be carried out after 4 hours or more. At the same time, the ambient temperature should be 20 ° , relative humidity - 65%. Drying is necessary under natural conditions. If humidity is reduced during this step, the drying period will be increased. Sometimes this mixture is used in conjunction with drying accelerators for polyurethane paints and varnishes, however, before the start of operation, a time of 7 days should be maintained. This is true when it comes to aggressive environments.
Application Precautions
"Tsinotan", technical characteristics, the properties of which were presented above, should be applied taking into account safety measures. The master should use personal protective equipment, namely:
- a mask;
- glasses;
- respirator.
If the mixture evaporates and enters the skin, inhalation of solvents should be avoided. Application should be carried out with a sufficient level of ventilation. It is necessary to exclude the entry of the primer into the respiratory tract, as well as the mucous membranes of the eyes. The product is considered a fire hazardous material.
Conclusion
“Tsinotan”, technical specifications, the price of which should be of interest to you if you plan to purchase this primer, is a tool that reliably protects metal structures. You can buy this mixture for 420 rubles. per kilogram. It is quite simple to use the composition, it is necessary to use a roller or brush to do this, and SOLV-UR acts as the recommended diluent. Use the same solvent or oil solvent to flush the equipment .
If you plan to use the technology of air spraying during application, the diameter of the nozzle of the tool can vary from 1.8 to 2.2 mm. In this case, the pressure can range from 0.3 to 0.4 MPa, which is approximately equal to 4 bar. The amount of diluent mentioned above can be used in a volume of 5% by weight.