Plastic is present in the decoration of many areas. Therefore, there are those who accept such material and actively mount it. But some people believe that it should not be in the house. Everyone makes a decision, but if you need fast and high-quality finishes for little money, then this is a suitable option. One has only to arm yourself with useful tips and know how to fix PVC panels to the ceiling.
Masters call several methods, there are simple and complex. For every person without experience, you need something lightweight. There are a lot of plastic panels on the market for sales; they are fixed approximately the same. It is important to understand that the basis for this has its own characteristics. At the first stage, it’s worth preparing everything you need and deciding what the surface will be after all work has been completed.
What should not be forgotten?
Before you go shopping, you need to know that there are PVC panels for ceilings and walls. But when the work is carried out in full, it is visually imperceptible which of them are stuck. But they are different in characteristics. And the main difference is that the ceiling material has a light texture so as not to burden the structure. But the wall is able to withstand maximum impact.
If you prepare the surface efficiently, then you can fix any of the options reliably. How to fix PVC panels to the ceiling? Before you start, you should decide whether maximum reliability is required from mechanical stress on the ceiling. There will not reach the children, pets. But the cost of the wall is about 30-40 percent more than the ceiling. Going to purchase, everyone will see on the shelves two main offers, these are:
The first option is the most common and many call it a plastic lining. The installation process is elementary, but they are not suitable for every interior, this is a minor minus. Most often, seamless patterns with glossy application are used. They look beautiful and at the same time will complement any interior. Of course, the joint is slightly noticeable, but in general, this is one of the best options.
Dimensions
How to fix PVC panels to the ceiling? The most important thing in such a process is to choose reliable elements that will withstand the entire structure. The best solution is metal profiles and screws. As for the sizes, basically the length goes in the range from 250 to 500 millimeters. The width will vary and depend on who the supplier of the products is, from 2.6 to 6 millimeters. Although there are always unusual options on the market, it’s better to trust trusted manufacturers who have been selling their products for more than a year.
Hardware
You can’t do without it. When work is carried out only on the ceiling, then you need to purchase a plinth. If the walls do not have an error, then the decorative option with a groove-lock is quite suitable. When there are some deviations, then this option will look ugly. Then you should take a regular profile and complete the robes. But then you can fix a vinyl ceiling plinth to it.
There is also a docking profile. It does not always need to be purchased, but let it be in stock. When the main stages are spoken, you can begin to work. In order for nothing to stand still, you will have to stock up not only with material, but also with all the necessary tools.
Create the foundation
As already noted, the fastening profiles will be organized identically for almost every panel. Therefore, you need to focus on other points. How to fix PVC panels to the ceiling? At the first stage, the foundation is being prepared. Today there are several basic options:
- A metal frame that is fixed from two profiles UD and Cd.
- Frame made of wood.
- The use of plastic guides.
- Fixing to the ceiling, without any additional additions.
The first is working with the wireframe. Before you properly install PVC panels on the ceiling, you need to create all the conditions for this. The use of galvanized profiles is considered one of the suitable methods. But to create everything, you need time, money. There is a plus in this - if you get tired of plastic, then they will dismantle it and do something else.
To create such a foundation does not need great skills. One has only to prepare everything necessary:
- Bulgarian.
- Drill.
- Screwdriver.
- Level.
- Connecting parts.
But there is also a minus in the creation of the frame, and this is filling the space by about 6 centimeters. If the ceilings are high, then it will be inconspicuous, in another situation you will have to think over. To create two types of profiles are required - guide and ceiling.
But this is not the whole set that will be required in the process of work. You will need a metal perforated suspension and dowels, and maybe an anchor, but attention is paid to the rough surface. To create a reliable mount, metal screws will be required. So you need to purchase the necessary elements. In order not to be mistaken, it is worth purchasing at least 150 pieces.
What is important to know? Before you go shopping, you need to do everything with a small margin of ten percent. This is needed on:
- Incorrect trim.
- Extra carving.
There are other moments when something needs to be repaired before the start of the main business. Mandatory tools - hammer drill and drill. Sometimes you can use a screwdriver. You will also need to cut metal profiles, while the master uses his assistant - a grinder or scissors.
Outline lines for work
To keep the surface level, you have to apply a level. The best one is laser, but it's expensive. So the hydraulic one is fine. Do not confuse it with a simple construction. With the help of such equipment, the highest and lowest points of the ceiling are determined. At the same time, there is no big difference in how to fix PVC panels to the ceiling of a balcony or kitchen. The whole process is the same.
Having found the lowest angle, about 50 millimeters are measured. So it becomes clear what material will be used to finish the ceiling. But this approach is individual, if it is supplemented by a heater, then the distance increases. From the selected angle you need to make marks over the entire area of the ceiling. You cannot do without the use of a hydraulic level. Next, apply the cord for horizontal upholstery.
After that, it is important to know how to fix the first PVC panel to the ceiling. It depends on how it is located, namely on the horizontal location the UD profile is fixed along the lower cut. For fixing, use a dowel or anchor. The distance between them should be approximately 60 centimeters. So, you need the groove to be located inside the room, since it will be necessary to fix the CD profile into it.
Then they start working with the CD profile, because it will be taken as a basis. For this, markings are made for the supporting installations. It is not so important what material this element is selected from - they should be perpendicular to each other. Any finishing material is laid in this way.
How to make a wireframe?
You need to understand how to create a crate. This procedure has several steps:
- For the design to be reliable, it is necessary to use suspensions for the CD profile.
- In order to create a crate, fasteners of the expansion bolt shield or anchor are taken. A flat surface will be obtained after marking. You need to use the same rope.
- After the suspensions are fixed at a distance of half a meter or more. The more often, the more convenient it is to carry out work, and even after dismantling it is possible to actually fix any other material.
- And having done the main thing, the profile is inserted into the grooves, after which the wings are removed and in the places of convergence are fixed with screws.
On this entire frame now you need to do the installation of finishing material. You can create a wooden crate, it is simpler and many will do it without problems. In addition, there is a plastic one. It is comfortable, practical, but does not withstand heavy loads.
Do not always need a crate
The question often arises, is it possible to fasten PVC panels without using an additional design? This is a very real task, especially in new buildings, where the ceilings are even. It is enough to putty the seams and you can apply the main finishing material. But how to fix PVC panels to the ceiling without a lathing? Self-tapping screws do not have to be used. For this, liquid nails are quite suitable, although you can take any other adhesive.
Moreover, this work has its own characteristics. How to fix PVC panels to the ceiling? If you smear the surface of the panel with glue, you will have to stand with it for a while. This is not suitable for everyone, and difficult.
No crate
How to fix PVC panels to the ceiling without lathing? It is worth performing simple steps:
- Lubricate the surface of the base material with adhesive and press for a short period to the ceiling so that everything is smeared.
- After which the surface is left for five minutes alone.
- Then fixation to the ceiling is made.
You don’t have to hold for long - there is an instant setting. When the base of the ceiling is concrete, it is treated with a primer before starting work, otherwise it will not work with the finish. The method is quick and will last a long time, but cannot be dismantled - everything just comes off.
We work with panels
How to fix plastic panels to the ceiling? This is the main work, so it is worth taking the process seriously. Regardless of which material is selected, the connection always has a spike groove. But the first is fixing the start profile. Installation is carried out in the same way as work with the main material:
- On the screws you need to fix the baseboard (when working with metal).
- In the case of a tree, they use a stapler.
- Kleimer fit for plastic guide.
- If there is no crate, then adhesive compositions are used.
After installing the starter rails, it's time for the panels themselves. The first tenon is fixed in profile, and on the other hand, from below, fixed with a self-tapping screw or other fasteners. The second and subsequent are also going. The main steps:
- Install the spike of the new panel into the groove.
- Press against guide.
- Commit.
Recommendations
And there are always questions for those who do the work for the first time. Specialists give such recommendations:
- It is necessary to measure the distance from the penultimate panel to the edge of the starting profile, after which five millimeters are removed from this distance and a cut is made.
- After that, the extreme panel is inserted with the cut-off side into the start profile before clamping. Everything should be smooth.
- How to fix the last PVC panel to the ceiling? Only after that you need to connect the spike and groove. Not everything will work out right away, but after trying there will be a result.
What next?
Further, it is important to correctly fix the ceiling plinth. There is a peculiarity in this process, and it does not matter how it is fixed - to glue or self-tapping screws. But you need to dock it in the corners accurately and accurately. The fact is that not all corners are perfect, and with the help of the wort they will not work perfectly. Yes, and many instructions are created exactly on the drafted project.
It is worth attaching it to one side and making marks. The same thing is done in the second panel. At these points, a reference point is made and after the baseboard is sawn off. The answer to the question "how to fix PVC panels to the ceiling in the bathroom" is voiced above, because the room does not matter - you just pay attention to the choice of material. The most important thing is not to disrupt the sequence of work.
Experts do not recommend fastening PVC panels to the ceiling with a stapler, since it is difficult and not so reliable, so it is not justified. Do not be afraid to start work such as ceiling cladding, because they are not complicated. When questions arise, it will not be difficult to solve them.