Feeder fishing today is very popular among both beginners and avid fishermen. The equipment in this case has a number of features. It can be purchased at a specialty store. However, it is much more interesting to make a feeder with your own hands. This is an exciting process.
A homemade feeder for the feeder is made of various materials. The choice depends on the fishing conditions, as well as on the type of fish. You can make several different instances of gear. How to attach them to the feeder will also be discussed later. The advice of experienced fishermen will help you figure this out.
The advantages of a homemade feeder
Each type of gear has its own consumables. These are its elements that can be left in the river for various reasons. In the feeder rod, these are a leash with hooks and a feeder. Therefore, going to a reservoir, such elements of gear should be in several copies. How to make a feeder for the feeder with your own hands? The advice of experienced fishermen will help you figure this out.
You can, of course, purchase consumables in a specialized store. This is a good solution when there is not enough time to create gear with your own hands. However, it is much more interesting to create feeders yourself. To do this, you need to show imagination, because for such a design a variety of materials can be suitable.
A homemade feeder has several advantages over purchased products. It is easy to manufacture. To create it does not require a lot of effort, time and resources. A homemade feeder for a feeder can have a different configuration and weight. This will allow you to choose the equipment that best suits the fishing conditions. This is an inexpensive product. Even if the feeder breaks off, you can not worry about its value.
In order for the equipment to withstand the load, adverse conditions of the bottom, you should also find out how to properly mount it. There are several installation options. They should be considered before being sent to a body of water.
FEEDER FEATURES
The second important point in the process of using bottom tackle is the question of how to attach the feeder to the feeder. The fact is that such a product can catch on a rocky bottom. Such a nuisance can happen when fishing from a steep edge with long casts. The feeder can not always overcome the bottom of shells.
With a dead hook on the feeder consumables, you will have to say goodbye. If the bottom topography impedes the easy movement of the feeder, you can lose a lot of them in one fishing trip.
To solve this problem, you should pay attention primarily to snap. To reduce the likelihood of a dead hook and cliff, a smaller diameter fishing line should be used to mount the feeder for the feeder . The loop of fastening of this element to the snap-in should be created from a thread of smaller diameter. The main line should be thicker. Such a loop protects the snap from tearing.
The difference in the cross section of the fishing line should be 0.01 mm. You can also use threads, the gap of which is performed at different loads. Having bought the appropriate varieties of fishing line, you need to try them at home. Which thread breaks first, that one is used to attach the feeder.
Materials
Feeder feeders for bream , pike, perch and other inhabitants of reservoirs can be made of various materials. If the current in the river is strong, one should pick up heavy varieties of products. For a quiet lake with stagnant water, it is better to choose light feeders.
Similar products should have good pop-up ability. To do this, the purchased equipment types include a metal sole. It serves simultaneously as an anchor and allows you to quickly raise the feeder from the bottom. To make tooling, the probability of a hook which will be minimal, it is necessary to take this feature into account.
To create such a feeder, it is necessary to prepare the appropriate materials. The most popular are metal, plastic. For the manufacture of a feeding trough, a building mesh, a case from photographic film, plastic from a bottle and even female curlers are suitable.
For a weight, tin, lead or a tertiary is suitable. You will also need to prepare a flexible and soft wire with a cross section of 0.7 mm. Will need pliers or pliers, wire cutters, scissors. If metal or tin is used, a tool will be required to carry out their cutting. You will also need a ruler, a hammer.
Create a weight
With the right choice of equipment, fishing will be an exciting pastime . Feeder feeders have a weight. It provides long-range casting, serves as an anchor and lifting force when fishing the product ashore.
To pour a weight, you must create a form. It is most often made from sheet metal. The thickness of the material should be 0.5 mm. Cutting is performed with scissors for metal. Next, the form is folded from the resulting workpiece (the weight configuration is taken into account). It should be as dense and accurate as possible. The possibility of hot metal spilling from the mold should be excluded.
When carrying out work, it is necessary to comply with safety regulations. Creating a weight is best done outdoors. When melting metal, harmful substances can be released. You should also exclude the possibility of hot metal getting on your skin. Otherwise, serious injury could result. All operations are performed in workwear.
Metal is melted on the grill or on gas. Before starting work, it is weighed. The weight must comply with the conditions of the reservoir. Feeder feeders for heavier flow . More metal is needed. It is melted on fire and poured into a mold. Its bottom can be covered with aluminum foil. After cooling completely, the weight can be removed from the mold.
Mesh feeder
Feeder fishing on the river is often done using a metal feeder. To make it, you will need a building mesh (5 x 5 mm cells), wire, wooden swimming trunks for even bending of the material, wire cutters, and pliers. From a sheet of size 1 x 1 m, you can create a dozen feeders.
From the grid you need to cut a cage to create a rectangular feeding trough. Its size is 21 x 8 mm. With a wooden plank, the material bends first by 3 cells, then by 5 cells. Then 2 more times it is done on 5 cells. There will be 3 cells at the end.
The first and last side combine on 1 cell. The grid will have a rectangular shape. The length of each side will be 5 cells. The sides can be fastened with wire. However, a lead weight also holds the mesh well.
After creating the shape of the feeder, a cast piece of lead or tin is installed in it. It must be well polished. Experienced fishermen recommend making the middle of the sinker thicker than the edges. In this case, the design will be more efficient. The weight is mounted on a metal mesh. Further, the feeder can be attached to the snap.
Plastic varieties
Many fishermen prefer to make plastic feeders for the feeder . In this case, you can create well-popped species that will allow you to catch different fish. For these purposes, many fishermen use ready-made plastic products. These can be containers for films, jars of vitamins or medicines, as well as women's curlers.
If necessary, such materials can be further processed. One-piece plastic containers can be drilled. To do this, you need to take a drill of the desired diameter. In this case, the fishing conditions are taken into account. If the water is calm, the holes can be made wider. The bottom can be cut at all. In this case, the bait can easily be washed out of the container. If the current is strong, the holes may be smaller. The bottom can be left.
Markings are made on the surface of the plastic. After drilling holes, a weight of the desired weight is attached to the workpiece. The loop for attaching to the snap can be made of a nylon cord or stainless wire.
Make the curler feeder even easier. You need to choose the correct diameter of the product. Curlers should be boiled. This will save the plastic from the specific smell of cosmetics. A weight is immediately installed on it. In this case, you will not need to drill anything.
Bottle plastic
A floating feeder for the feeder , which will not often break due to a dead hook, is also created from bottle plastic. From a unit of two-liter containers, up to 6 medium feeders can be made. It is better to choose durable material.
First, the bottom and neck are cut from the bottle. Rectangular plastic is cut along. Using a marker, the dimensions of future feeders are applied to it. Most often they are made with a size of 6 x 13 cm. The points of the holes should be applied to the plastic in a checkerboard pattern. The distance between them should be 2 cm.
Then, using ordinary scissors, future feeders are cut out. The material is rolled into cylinders. The overlap is 1 cm. It is fixed with the help of a clerical stapler. Holes are cut with a soldering iron. An ordinary hole punch is also suitable for this. A metal plate is put on the workpiece. Make a device for mounting. It is made of wire.
Benefits of Bottle Plastic
A homemade bottle feeder made of plastic bottle has many advantages. She's worth a dime. Moreover, the manufacturing process does not take much time. A feeder made of this material has a good pop-up capacity. Experienced fishermen argue that with a depth at the casting point of up to 7 m at a distance of 30 m from the shore, the presented product is shown on the surface literally 8-9 m when the line is reeled up. The handle of the pi coil makes about 11-13 revolutions. In this case, the feeder literally jumps on the surface of the water surface.
The presented product allows you to catch various fish on distant brows. Losing such a coil will be much more difficult than metal varieties. The transparent case also has a number of advantages. Fish can see the bait. If it is in an opaque container, it can reduce the interest of aquatic inhabitants.
Unlike purchased varieties, the plastic version will never roll. The feeder will lie clearly with the load down. This is due to the large difference in weight between the lead plate and the main material of the product. The fishing line will also not get tangled or twisted.
Fixing Methods
There are many ways to attach a feeder to a feeder . Experienced fishermen at the same time take into account the characteristics of the tackle itself, its weight. There are light, super light, medium, heavy and very heavy varieties. Universal is considered light tackle. It allows you to fish out both small and medium-sized fish from the water.
As mentioned above, the main fishing line and the thread of the feeder should be different in thickness. This will prevent a frequent break. You can fix the feeder itself in different ways. Most often, special knots fit. To speed up the installation process, many fishermen switched to various carbines, swivels and other additional elements.
You can create a mount immediately before fishing in a pond or at home. Transporting the rod will be easier if you attach the feeder immediately before being thrown into the water. However, it depends on the preferences and habits of the angler.
A powerful, durable fishing line must be chosen for catching large fish or when making very distant castings. For medium and small production fine monofilament is suitable.
If you attach the feeder feeder directly to the fishing line, you can subsequently spend a lot of time when unraveling the nodes after trimming the snap or its break. To prevent this, it is recommended to use mini-carabiners. Such fasteners provide high speed removal and installation of the feeder. At the end of fishing with a carabiner, it will be easy to unfasten the equipment and pack the rod for further transportation.
Gardner loop
One of the most famous snap fastener techniques is the Gardner loop for the feeder. How to knit it? There is a simple instruction. Such a unit allows you to firmly set the feeder on the fishing line.
The thread must be passed through each ring of the rod. Further, about 30 cm recedes from its end. The fishing line bends twice. Having departed from the folded section of 15 cm, a second bend should be made. This loop is for feeding troughs.
A large bend should be passed through the swivel. It will not allow the thread to twist. Next, a carabiner must be inserted into the loop. The feeder is attached directly to it. The swivel is mounted on top.
To tighten the loop, the line must be moistened with water. This will give strength to the unit when it is tightened. Next, you can install the leash with a hook. How to knit a Gardner loop for a feeder? This allows you to understand the advice of experienced fishermen. After carrying out all the above manipulations, you can start fishing.
Having considered how to create a homemade feeder for the feeder, each angler will be able to independently make and install it on the tackle.