A visit to the hairdresser sometimes becomes an unnecessary luxury, and a man’s haircut with a machine is not such a difficult thing. Having mastered it, you will simultaneously fall into two birds with one stone: you will save the family budget from unnecessary expenses and master the skill with which you can earn some good money.
First, remember a few rules. Men's haircut machine is done on short hair. Therefore, if your client is too overgrown, remove all excess length with scissors. And the machine itself, comb, nozzles and scissors for thinning should be kept clean, neatly folded in a box.
Wizard Tips
- Any new craft requires some skills, and a man's haircut with a machine is no exception. Until you get them, you can leave the hair of the model a little longer than usual.
- In the process of work, the movements of your hands should be slow, smooth and free.
- It should be cut gradually, removing hair a little.
- During the haircut, you need to comb your hair more often so that they are cut evenly.
Process technology
So let's get started! Model hair should be dry and preferably washed. Clean hair is better placed in the hairstyle, and the blemishes of work on them are better visible. Therefore, on a washed head, any haircut is more conveniently adjusted.
First, use the nozzle of the largest caliber (12 mm) and cut the hair in the crown of the head, somewhat capturing the temporal part. We act with the comb from the roots down, and with the machine, on the contrary, against the growth of the hairline, starting from the face. We do the work carefully, all the while maintaining the same angle at which we press the machine to the head. The quality of the process will depend on how often the hair is combed - the more often, the better!
Men's haircut with a typewriter at home requires great care. Before proceeding to the next stage, you should carefully examine the model’s head - if there were any strands left untreated by the device. When the inspection is completed, you can go to the back of the head.
For this, the nozzle is changed to a smaller one - from 9 to 6 mm. Haircut is made from the bottom up. In the region of the crown of the head, the machine cannot be pressed firmly against the head - to even out the length of the hair. Whiskey is cut with the same nozzle. Male haircut machine at this stage involves combing hair in different directions.
At the final stage, shear without nozzles. It is important to gradually switch from the parietal zone to "no." The edging line of the neck, behind the ears and temples should be smooth, uniform, without bald spots. It is difficult to achieve this, so act slowly. Then, with ordinary scissors, hairs that do not fall under the machine are trimmed. And with scissors for thinning we correct inaccuracies and blemishes.
Hairstyle "Site"
The men's haircut “Playground” became fashionable after the mass audience met the terminator Schwarzenegger. Since then, it has been very popular among young people and adolescents. Not everyone can do such a hairstyle - hair for her should be thick, stiff so that they can hold the desired shape.
Men's haircut "Site" It is made with straight scissors, a machine, a comb and a hairdryer. And the skill level is required slightly above average. The most difficult thing is to design this very “platform”, which is located from the forehead to the crown and forms a strictly horizontal surface. Create a surface should be especially careful. Hair should be lifted vertically upwards and pulled to yourself. With both hands you should work simultaneously, while combing and scissors.
Wizard Tips
- To begin with, the hair is washed, sprinkled with a fixative and dried with a hairdryer in the “on end” position.
- The length of the strands should not be more than 5 cm - remove the excess in advance.
- I cut from the sides. Pull hair perpendicular to the future site. Work in the direction from the front to the back of the head. The position of the scissors and comb is appropriate. So the whiskey and the back of the head are cut.
- The hair below is shortened almost to the roots. You can do this with a typewriter.
- Now we are forming the site. Trimming the approximate strand in the face, then the same - on the top of the head. We make a vertical parting, connecting both trimmed locks, and we obtain the control.
- On the control strand, we cut out all the hair in the parietal zone with a horizontal parting. Then we fringe the whole cropped head.
- Whiskey should be made straight!