The requirements for underwater cameras are strict. In this case, the tightness of the housing is evaluated. The pressure of the underwater camera for fishing should withstand a lot. Many lenses are not suitable for this. It is also important to mention lighting. You can assemble the camera yourself at home. However, in this case, it is necessary to determine all the components.
Conventional Camera
This type of underwater camera is made for fishing with your own hands using a high-frequency compression unit. In this case, you will also need two LEDs. However, in the first place, it is important to assemble the model case. Some experts in this situation advise using a plastic pipe. The lens must be installed immediately with the module. It must connect to a flash drive.
It should also be noted that a home-made underwater camera for fishing will not work without a central processor. It should be installed at the compression unit. Directly the matrix is selected low resistance. At the end, the underwater fishing chamber is equipped with a battery and an output port.
Using compression units at 50 Hz
An underwater camera for do-it-yourself fishing is done with a 50 Hz unit quite simply. In this case, a small plastic pipe fits perfectly. Some experts additionally wrap it with plastic wrap. LED lamps are connected to the device through a conductor.
The lens can be selected with the module. The filter itself will require an optical type. After installing the matrix on the unit, a special prism is mounted, which is designed to transmit images to the central processor. To save data, the underwater camera for fishing is equipped with a flash drive. Batteries in this case can be used with finger batteries.
Application of compression units at 60 Hz
An underwater camera for do-it-yourself fishing is done with this unit only using a matrix with a converter. For winter fishing, this model works well. Directly, many experts recommend selecting a lens with a module. However, the filter will fit the usual. It is recommended to start assembling the camera by securing the unit. Next up is the optical filter. After soldering the matrix, LED lamps are attached. In this case, one is not enough for sure. Then it remains only to install the batteries and flash drive with access to it.
Using Chromatic Capacitor
It’s quite difficult to assemble an underwater camera for DIY fishing with a chromatic compressor. The problem in this case is that a low-frequency compression unit is required. Find it in the store is difficult. Also, to assemble the model you will need a high-quality lens. Directly housing can be made with plastic pipe.
In this case, high density polyethylene tape should be used. However, in the first place, it is important to deal with the installation of a capacitor. To this end, you will have to solder the matrix immediately. Next, you need to install the optical filter. Directly, the lens is well suited for the modular type. The central processor should only be connected after the flash drive. Also, an underwater webcam for fishing is equipped with a shutter. Use it more expediently from a video camera. Batteries in this case can be used with finger batteries.
Camera with a magnetic filter for winter fishing
A camera for underwater fishing with magnetic filters is nowadays widespread. In this case, its advantage is compactness. The compression unit can even be used at 50 Hz. Directly there is an opportunity to make a case out of a can. In this case, a sealed plastic bag is required first. However, first of all, it is important to deal with the device of the matrix, as well as the lens. For this purpose, a central processor is installed in the case. A flash drive in this situation can be used small. The shutter must be installed at the compression unit itself. Last of all, it will be necessary to tackle the battery and port.
Convection Condenser Model
On a convection condenser, an underwater camera for fishing reviews, as a rule, gets positive. Even at great depths, she behaves normally. To assemble the model yourself, you need a durable and long plastic case. As insulation, you need to use a plastic tape. It must be laid in several thin layers. The capacitor in this case will be installed near the matrix. However, first of all, the compression unit is prepared. With this capacitor, it is more advisable to choose it at 55 Hz. At the same time, many experts recommend using a matrix with two converters.
All this will allow you to take pictures in high resolution. However, the lens must match the matrix. In this case, many prefer models with optical filters. Directly magnetic counterparts wear out quickly and are expensive in stores. After installing the compression unit, a prism is fixed in the camera body.
The shutter in the device should be located near the capacitor. To connect a flash drive will have to use a blowtorch. At the end of the work, you need to do the installation of the port. In some cases, thermal relays are used for such cameras, but it consumes a lot of energy from the battery.
Device with dipole diode
An underwater camera for winter fishing with dipole diodes is made very simple. For this purpose, a compression unit will need a standard at 50 Hz. In this case, only modular lenses are used. The case is standardly selected plastic. Matrices for these purposes are suitable with one converter. Direct filters are more appropriate to install the optical type.
The central processor in the camera body must be mounted on the compression unit. After fixing it, you can proceed to install the flash drive. In this case, for the battery, the ports are placed on the matrix. At the end of the work, LED lamps are selected for lighting.
The use of silicon diodes
Underwater camera for winter fishing with silicon diodes in our time is in great demand. First of all, the models stand out because they do not consume a lot of electricity. In order to fix them, you need to use the compression unit only at 60 Hz. Find it in stores is not difficult. The matrix itself is mounted on two transducers.
Lenses should be mounted on the compression unit. Additionally, you need to provide a place in the housing for the shutter. You can use it from any camcorder. A flash drive is connected as standard directly to the matrix. Then it remains only to solder the central processor. The battery port must be installed at the back of the camera.
Use of low sensitivity resonators
Low-sensitivity resonators for camera assembly fit well. However, the matrix for this must be selected with one converter. All this will allow, ultimately, to put the usual compression unit at 50 Hz. It is more expedient to install filters in the chamber of absorbing type. However, first of all, you need to do the lens.
In some cases, it is placed on the seal. Thus, you can not worry about water leaks. The central processor in such models is located immediately behind the compression unit. The battery should normally be in the back of the camera.
Use of highly sensitive resonators
Highly sensitive resonators allow you to shoot high-resolution images. However, it should be borne in mind that in this case the battery will be quickly discharged. To begin the assembly of the model you need to install the compression unit. Next, you should deal directly with the resonator. In order to install it, you must first put the matrix.
The next step is preparing the optical filter. Magnetic counterparts for such cameras will not fit unambiguously. A flash drive can be used small. The central processor must be installed at the compression unit. In order to put a serial port, you need to fix the shutter first. At the end of the work, a battery is put.