Fans of winter sports who have already managed to choose a board to conquer the mountain peaks must definitely be guided in how to correctly install the mount on the snowboard. The presence of such knowledge will allow you to adjust the board based on personal preferences and the chosen riding style.
Snowboard mount structure
The standard snowboard mount includes the following set of elements:
- base;
- highback;
- gas pedals;
- upper and lower strep;
- wheels.
Since the clips of the mounts always look outward, in practice it is quite easy to distinguish between the left and right mounts of the snowboard. Just look at the disk on which there are designations in degrees from 0 in both directions. The presence of additional holes in the disk due to the need to adjust the mounts in the front and the opposite direction.
How to install the mount on the snowboard, based on the rack?
When installing the fasteners, it is important which foot the rider prefers to stand on the board while moving. It is not easy for beginner snowboarders to immediately choose the right stance. Basically, everything is learned in practice.
However, there is still an effective way to determine the most convenient rack at home. To do this, you need to get a small push in the back. Which leg will move forward first, that, most likely, is the leading one when snowboarding. To verify the result, it is worth repeating the experiment several times.
If the right leg was in front, in this case, it is necessary to install the mount on the snowboard, designed for this leg, closer to the nose of the board. Based on the nature of the placement of the lead mount, the width of the rack will subsequently be adjusted. A wide stance is convenient for some riders, and a narrow one for others. Beginner snowboarders are advised to set up a stance of medium width.
Mount Settings
Before proceeding directly to the installation of fasteners, you must try them on with your boots. This is required to configure the gas pedal. This element is regulated from the base. To understand this issue, you need to place the boot in the mount, fastening the lower and upper straps. Next, the gas pedal should be set in such a position that it reaches the bend of the toe on the sole.
How to install the mount on the snowboard? It is necessary to center the straps. For this, there are special tools for adjusting the back of the clip. In addition, you need to pay attention to ensure that the highback runs tightly to the boot.
How to install a mount on a snowboard with a high level of rigidity?
If a rigid board with the appropriate type of boots is available, then it is better to install the mounts according to the so-called carving rack, which makes it possible to make sharp, sharp turns at high speed distances.
The angles of fastenings on hard snowboards are determined by the width of the board. First, install the rear mount so that the socks peek out slightly behind the board. At the same time, the heels should be located clearly above the back edge. This will allow maximum pressure on the edges of the board.
The front mount should be installed at the angle of the rear mount, adding about 8 about to its position. In the future, it will be possible to adjust the angles for a comfortable ride, based on individual wishes.
Attaching Mounts to Standard Soft Boot Boards
How to install the mount on the snowboard standard model? You should try it, starting with setting the standard settings for these types of boards, which involve adjusting the fasteners according to the angles + 21 ° / + 6 °. When determining the most convenient rack in practice, it will be possible to slightly change the settings of angles of the order of 3-4 about in the necessary direction.
Rack alignment
To understand how to properly mount the mount on the snowboard, you need to deal with the issue of centering the rack. This is required to align the legs relative to the width of the snowboard, which helps to stabilize turns during movement.
The best way to center the rack is to put on shoes with mounts, and then try to feel where the leg should be in relation to the mounting discs. At the same time, installing a snowboard mount on a snowboard for a beginner may be somewhat difficult, as some fasteners have a fixed heel. In other models of fastenings, the heel can move in both directions, which contributes to a more convenient change in the position of the boot.
Rack width
Under the width of the rack should be understood as the distance between the center points of the individual mounts. In order to understand how to correctly mount the mount on the snowboard, in this case, you need to build on the parameters of your own growth.
The width of the rack should exactly equal the distance from the ground to the middle of the rider's kneecap or be 2.5 cm greater than his shoulder width. The rack width parameter thoroughly affects the ability to control the behavior of the board. The widest stance gives stability to movement, but complicates the edging change. The opposite effect is felt when reducing the width of the rack.
Understanding how to properly mount the mount on a snowboard, based on the width of the rack, is important for freestylers, who often consciously increase this figure to perform complex tricks. While downhill enthusiasts often prefer narrow racks.
Novice riders are encouraged to use a natural stance, resorting to the default settings indicated above. Independent change of this parameter seems advisable only for experienced snowboarders who are able to distinguish in practice the effect of adjusting individual settings.